Ultrasound assisted extraction of phenolic compounds from grapes.

C. Carrera,A. Ruiz-Rodríguez,M. Palma,C. Barroso

DOI: https://doi.org/10.1016/j.aca.2011.11.032

IF: 6.911

2012-06-30

Analytica Chimica Acta

Abstract:

What problem does this paper attempt to address?

Development and properties of dental Ti–Zr binary alloys

Jie Jiang,Chuan Zhou,Yanwei Zhao,Fuming He,Xiaoxiang Wang

DOI: https://doi.org/10.1016/j.jmbbm.2020.104048

IF: 4.042

2020-01-01

Journal of the Mechanical Behavior of Biomedical Materials

Abstract:In this study, two medium Zr-containing Ti-based alloys with commercially pure titanium as control were systematically investigated to assess their potential biomedical application. After samples subjected to TMP and CR, it was found that the Zr addition significantly affected the microstructure, phase constitutions, mechanical properties and cytocompatibility. The microstructural results showed that increasing Zr concentrations resulted in more refined grains. Furthermore, Zr changed the phase constitution: CR Ti–20Zr was formed by the single α-phase while CR Ti–30Zr alloy was formed by the coexistence of α and deformation-induced FCC phases. The P-type FCC phase was dominant and more prone to occur than the B-type one. The mechanical tests demonstrated that the increasing Zr content led to a simultaneous increase in micro-hardness, strength and plasticity of CR samples due to the combined effects of solution strengthening, work hardening and the FCC phase. The SEM fractography indicated that the brittle fracture of CR Ti–20Zr due to deformation twins and ductile fracture of CR Ti–30Zr because of FCC phase. Furthermore, Ti–Zr alloys presented comparable cytocompatibility to the CP-Ti control based on cell viability, proliferation and intracellular O2− content of MSCs. Specifically, alkaline phosphatase activity in BMSCs were significantly higher for grain refined CR Ti–30Zr. Considering all these results, CR Ti–30Zr alloy exhibited the optimal comprehensive performance to be potential dental materials.
Ti-Zr-Nb-Ta-Sn Medium-Entropy Alloys with Excellent Properties as Potential Biomaterials

Dandan Zhu,Shiwen Hu,Guofeng Zhang,Yongfan Fu,Dexue Liu

DOI: https://doi.org/10.1007/s11665-024-09656-4

IF: 2.3

2024-06-05

Journal of Materials Engineering and Performance

Abstract:This study aimed to develop a new alloy for orthopedic implants by combining the concept of medium-entropy alloys (MEAs) with the performance requirements of medical alloys. The effects of Sn on microstructure, mechanical properties, electrochemical behavior, wettability, and friction & wear properties of Ti 40 Zr 40 Nb 5 Ta 15-x Sn x ( x = 3, 5, 7; at.%) MEAs were investigated. The results indicated that the Ti-Zr-Nb-Ta-Sn MEAs exhibited a single-phase BCC structure with lattice parameters of 0.3420 nm, 0.3439 nm, and 0.3447 nm, respectively. The alloys performed high yield strength (863 ± 7 ~ 1101 ± 8 MPa) with elongation up to ~ 10.6%, and hardness (291.6 ± 4.2 ~ 323.4 ± 3.2 HV). At the same time, these alloys showed the low Young's modulus (55.8 ± 1.3 ~ 68.0 ± 1.6 GPa). In the phosphate buffer saline (PBS) solution, the alloys displayed corrosion resistance comparable to that of the Ti6Al4V alloy, indicating it got excellent corrosion resistance. In the medium of deionized water and PBS solution, the alloys exhibited hydrophilicity. The wear resistance of the alloys increased substantially with increasing Sn content. In conclusion, Ti-Zr-Nb-Ta-Sn MEAs possessed high yield strength, relative low Young's modulus, and good corrosion and frictional wear resistance, making them promising materials for medical orthopedic implants.

materials science, multidisciplinary
New TiTaNbZrMo high-entropy alloys for metallic biomaterials

Chenwei Li,Ying Ma,Xu Yang,Minghao Hou

DOI: https://doi.org/10.1088/2053-1591/ac2f0b

IF: 2.025

2021-10-01

Materials Research Express

Abstract:Abstract The advantages of high entropy alloy with good comprehensive properties provide a potential opportunity to explore and develop new alloys suitable for human implantation. In this experiment, TiTaNbZrMo high entropy alloy was designed and prepared by alloy design and first principle. The calculation results predict that the phase composition of each high entropy alloy is BCC structure, and the designed high entropy alloy has structural stability; the non-equal atomic ratio TiNbTaZrMo high-entropy alloy has higher ductility than the equal atomic ratio TiNbTaZrMo high-entropy alloy; the B/G, Poisson’s ratio υ and ( C 12 - C 44 ) values of Ti 30 (NbTaZr) 60 Mo 10 alloy are the largest, indicating that the toughness of this alloy is the best, and the Young’s modulus value is the smallest. The experimental results show that the yield strength of Ti 30 (NbTaZr) 60 Mo 10 alloy is 1132 MPa, the plastic strain is 33%, and the wear resistance and corrosion resistance are good. The potential of Ti 30 (NbTaZr) 60 Mo 10 in biological field is proved by calculation and experimental test, which provides an important basis for its industrial application in biomedical alloy.

materials science, multidisciplinary
Investigations on microstructure and properties of Ti-Nb-Zr medium-entropy alloys for metallic biomaterials

Meichen Hu,Li Wang,Qianli Huang,Yang Liu,Junyang He,Hong Wu,Min Song,Gen Li

DOI: https://doi.org/10.1016/j.intermet.2022.107568

IF: 4.075

2022-06-01

Intermetallics

Abstract:In this study, three medium entropy alloys (MEAs), TiNbZr, Ti1.5Nb1.5Zr and Ti1.5NbZr1.5 were designed and investigated to be applied as biomedical materials. The results showed that the alloys prepared by arc melting have a typical dendrite microstructure, caused by elemental segregation during solidification. With composition changes, the partition of the constituting elements behaves differently. The microstructure inhomogeneity and chemical segregation could be greatly reduced by homogenization treatment. The MEAs show good compressive ductility (>40%) and yield strength comparable to or even superior to those of the commercially used biomedical alloys (e.g., 316 stainless steel and pure titanium), which are mainly contributed from the solid-solution strengthening effect. In addition, these MEAs exhibit acceptable Young's modulus ranging from 80 to 93 GPa by nano-indentation tests. The alloys also show excellent corrosion resistance in the phosphate buffer saline (PBS) solution and favorable cyto-compatibility, which are comparable to or even superior to pure titanium and/or Ti-6Al-4V alloys. Based on these properties, the Ti-Nb-Zr MEAs show a promising potential in biomedical applications. The results in this study could be instructive for further alloy design of such biomedical MEAs.

materials science, multidisciplinary,chemistry, physical,metallurgy & metallurgical engineering
Biocompatible As-Cast and Homogenized TiNbTaZrMoV High Entropy Alloys: Mechanical Properties, Corrosion Resistance and in Vitro Studies

Kuan-Cheng Lai,Shih-Chieh Chao,Ko-Kai Tseng,Jien-Wei Yeh,Po -Yu Chen

DOI: https://doi.org/10.1016/j.jmrt.2023.05.201

2023-01-01

Abstract:Commercial 316L SS, CoCrMo, and Ti6Al4V alloys have been widely used as implant materials for biomedical applications. However, the inadequate wear resistance and the released metal ions could result in inflammation, cytotoxicity, and shorten the lifespan of surgical implants. To extend the service life and durability of metallic biomaterials, the TiNbTaZrMoV HEA was developed by integrating biocompatibility characteristics with the unique properties of high-entropy alloys (HEAs). Both as-cast TiNbTaZrMo and TiNbTaZrMoV HEAs consisted of dual BCC phases in the dendritic structure: the dendrite region was enriched with Ta, Mo, and Nb, while Zr, Ti, and V were concentrated in the interdendrite region. The homogenized TiNbTaZrMoV HEA possessed a single BCC phase with a homogeneous component distribution. Moreover, the wear resistance of the homogenized TiNbTaZrMoV HEA was superior to the as-cast TiNbTaZrMo and TiNbTaZrMoV HEAs. In terms of electrochemical behaviors, the homogenized TiNbTaZrMoV HEA exhibited superior corrosion resistance compared to the other commercial metallic biomaterials in phosphate-buffered saline solution at 37 °C. The in vitro biocompatibility evaluation revealed that the homogenized TiNbTaZrMoV HEA could support the attachment and proliferation of the MC3T3-E1 cells, presenting good biocompatibility comparable to the Ti6Al4V alloy. This study demonstrated the feasibility of the homogenized TiNbTaZrMoV HEA for orthopedic bioimplant applications.
Development of non-equiatomic Bio-HEAs based on TiZrNbTa-(Mo and Mn)

Jhuliene Elen Torrento,Tiago dos Santos Pereira de Sousa,Nilson Cristino da Cruz,Gerson Santos de Almeida,Willian Fernando Zambuzzi,Carlos Roberto Grandini,Diego Rafael Nespeque Correa

DOI: https://doi.org/10.1063/5.0100465

IF: 6.6351

2022-09-01

APL Materials

Abstract:This study produced non-equiatomic TiNbZrTaMn and TiNbZrTaMo high entropy alloy (HEAs) by argon arc-melting and heat-treated for microstructural homogenization. The phase composition, microstructure, and selected mechanical properties were measured and compared with theoretical predictions. Additionally, electrochemical and cytotoxicity tests evaluated their potential applicability for use as biomaterials. X-ray diffraction measurements patterns showed a single BCC phase for the TiNbZrTaMn and a secondary HCP phase for the TiNbZrTaMo sample. The microstructural analysis revealed the formation of irregular grain boundaries and some lamellae formation, with chemical segregation of the alloying elements at the sub-micro-scale. The samples exhibited elastic modulus (80–110 GPa) closer to CP-Ti grade 2 (100 GPa) and higher Vickers microhardness (450–550 HV) than Ti–6Al–4V alloy (400 HV). The electrochemical and biological tests indicated a superior corrosion resistance against 0.9% NaCl solution compared with commercial metallic biomaterials, with proper cell adhesion and viability of pre-osteoblastic cells and hydrophilic behavior. Altogether, the data indicate that TiNbZrTaMn depicts better applicability potential for being used as a biomaterial in biomedical applications than some commercial materials (SS 316L, CP-Ti grade 2, and Ti–6Al–4V), mainly considering load-bearing orthopedical implants.

materials science, multidisciplinary,physics, applied,nanoscience & nanotechnology
Experimental and DFT Investigations of AlNbTiVZr High Entropy Alloys with Excellent Mechanical Properties

Hongwei Yan,Yong’an Zhang,Wei Xiao,Boyu Xue,Rui Liu,Xiwu Li,Zhihui Li,Baiqing Xiong

DOI: https://doi.org/10.1007/s40195-024-01716-x

2024-01-01

Acta Metallurgica Sinica (English Letters)

Abstract:This study investigated the microstructure and mechanical properties of AlNbTiVZr series high-entropy alloys (HEAs) through both experimental studies and density functional theory calculations. Significant improvements in the microstructures and mechanical properties were achieved for the AlNbTiVZr series HEAs by meticulously adjusting the alloy composition and employing homogenization heat treatment. Notably, the specimen designated as Al0.5NbTiVZr0.5 demonstrated excellent mechanical properties including a compressive yield strength of 1162 MPa and a compressive strength of 1783 MPa. After homogenization heat treatment at 1000 °C for 24 h, the Al0.5NbTiVZr0.5 alloy exhibits brittle-to-ductile transition. Further atomic-scale theoretical simulations reveal that the decrease of Al content intrinsically enhances the ductility of the alloys, thereby indicating that the mechanical properties of the AlNbTiVZr series HEAs were significantly influenced by the chemical composition. Additionally, specific atomic pair formations were observed to adversely affect the microstructure of the AlNbTiVZr series HEAs, particularly in terms of ductility. These findings provide valuable insights for the design and optimization of light weight HEAs, emphasizing the synergistic adjustment of alloy composition and heat treatment processes to achieve a balance between the strength and ductility.
Design and properties of novel Ti–Zr–Hf–Nb–Ta high-entropy alloys for biomedical applications

Wei Yang,Shujie Pang,Ying Liu,Qing Wang,Peter K. Liaw,Tao Zhang

DOI: https://doi.org/10.1016/j.intermet.2021.107421

IF: 4.075

2022-02-01

Intermetallics

Abstract:The novel high-entropy alloys (HEAs) with compositions of (Ti1/3Zr1/3Hf1/3)15(Nb1/2Ta1/2) x (x = 3, 5) for biomedical applications have been designed and synthesized, using the cluster formula approach. The present HEAs have a single body-centered-cubic (BCC) solid-solution structure and possess prominent mechanical properties of high compressive yield strength (834–890 MPa) and microhardness (287–293 Hv), large plasticity (>45%) under compression, as well as low Young's moduli (56–68 GPa). Also, these HEAs exhibit good bio-corrosion resistance, as revealed by a low corrosion rate at the order of 10− 4 mm/year and the low passive current densities of 10− 2 – 10− 1 A/m2, which are attributed to the formation of passive films consisting of Ti-, Zr-, Hf-, Nb-, and Ta- oxides. The high cell viability and proliferation of bone-forming MC3T3-E1 cells on the HEAs are comparable to those on the Ti–6Al–4V alloy, indicating their good biocompatibility. The present work demonstrates the great potential of these novel Ti–Zr–Hf–Nb–Ta HEAs for biomedical applications.

materials science, multidisciplinary,chemistry, physical,metallurgy & metallurgical engineering
Structure and properties of Ti-rich Ti–Zr–Nb–Mo medium-entropy alloys

Ka-Kin Wong,Hsueh-Chuan Hsu,Shih-Ching Wu,Wen-Fu Ho

DOI: https://doi.org/10.1016/j.jallcom.2021.159137

IF: 6.2

2021-07-01

Journal of Alloys and Compounds

Abstract:In this study, three nonequiatomic Ti-rich Ti–Zr–Nb–Mo medium-entropy alloys (Ti-MEAs), namely Ti50–Zr25–Nb15–Mo10, Ti58–Zr23–Nb12–Mo7, and Ti65–Zr20–Nb10–Mo5, were developed for biomedical applications. All the Ti-MEAs exhibited a single body-centered cubic structure. Furthermore, the Ti-MEAs exhibited a higher yield strength (1381–1754 MPa) and lower elastic moduli (86.4–109.6 GPa) than Ti–6Al–4V ELI, 316L stainless steel, and Co–Cr–Mo alloys did. The resilience of the developed Ti-MEAs was> 11 MJ/m3, which is multiple times that of most commercial implants. The excellent yield strengths of the three Ti-MEAs were attributable to the lattice distortion effect caused by the alloying atomic radius difference (δ). Increasing the Ti content of the alloys could prevent the segregation problem and reduce the elastic modulus of the alloy. The produced Ti-MEAs (with Ti contents of> 50 at%) are promising alloys because they have excellent yield strength and low elastic modulus and do not exhibit the segregation problem.

materials science, multidisciplinary,chemistry, physical,metallurgy & metallurgical engineering
A Review: Design from Beta Titanium Alloys to Medium-Entropy Alloys for Biomedical Applications

Ka-Kin Wong,Hsueh-Chuan Hsu,Shih-Ching Wu,Wen-Fu Ho

DOI: https://doi.org/10.3390/ma16217046

2023-11-05

Abstract:β-Ti alloys have long been investigated and applied in the biomedical field due to their exceptional mechanical properties, ductility, and corrosion resistance. Metastable β-Ti alloys have garnered interest in the realm of biomaterials owing to their notably low elastic modulus. Nevertheless, the inherent correlation between a low elastic modulus and relatively reduced strength persists, even in the case of metastable β-Ti alloys. Enhancing the strength of alloys contributes to improving their fatigue resistance, thereby preventing an implant material from failure in clinical usage. Recently, a series of biomedical high-entropy and medium-entropy alloys, composed of biocompatible elements such as Ti, Zr, Nb, Ta, and Mo, have been developed. Leveraging the contributions of the four core effects of high-entropy alloys, both biomedical high-entropy and medium-entropy alloys exhibit excellent mechanical strength, corrosion resistance, and biocompatibility, albeit accompanied by an elevated elastic modulus. To satisfy the demands of biomedical implants, researchers have sought to synthesize the strengths of high-entropy alloys and metastable β-Ti alloys, culminating in the development of metastable high-entropy/medium-entropy alloys that manifest both high strength and a low elastic modulus. Consequently, the design principles for new-generation biomedical medium-entropy alloys and conventional metastable β-Ti alloys can be converged. This review focuses on the design from β-Ti alloys to the novel metastable medium-entropy alloys for biomedical applications.
CASP9 results compared to those of previous casp experiments

A. Kryshtafovych,K. Fidelis,J. Moult

DOI: https://doi.org/10.1002/prot.23182

Abstract:The quality of structure models submitted to CASP9 is analyzed in the context of previous CASPs. Comparison methods are similar to those used in previous articles in this series, with the addition of new methods looking at model quality in regions not covered by a single best structural template, alignment accuracy, and progress for template‐free models. Progress in this CASP was again modest and statistically hard to validate. Nevertheless, there are several positive trends. There is an indication of improvement in overall model quality for the midrange of template‐based modeling difficulty, methods for identifying the best model from a set generated have improved, and there are strong indications of progress in the quality of template‐free models of short proteins. In addition, the new examination of a model quality in regions of model not covered by the best available template reveals better performance than had previously been apparent. © Proteins 2011; © 2011 Wiley‐Liss, Inc.
Achieving superior mechanical properties and biocompatibility in an O-doping TiZrNb medium entropy alloy

Lijun Wu,Xinyue Yang,Tianxin Li,Lei Li,Yiping Lu

DOI: https://doi.org/10.1016/j.intermet.2023.107991

IF: 4.075

2023-10-01

Intermetallics

Abstract:The present work aimed to develop a novel medium entropy alloy (MEA) with superior mechanical properties and biocompatibility for the metallic-bioimplant application. A series of (TiZrNb0.7) 100-x O x (x = 0, 0.5, 0.75 at. %) MEAs were carefully designed and prepared. The microstructure, mechanical properties, corrosion resistance, and biocompatibility were investigated in detail. Single-phase body-centered cubic (BCC) structural (TiZrNb0.7) 100-x O x MEAs consisted of as-cast dendritic morphology. Interestingly, the yield strength and ductility of (TiZrNb0.7) 100-x O x MEAs were improved simultaneously with their O concentration. The (TiZrNb0.7)99.25O0.75 MEA had optimal mechanical properties, exhibiting a yield strength of 911 ± 11 MPa, a fracture elongation of 16.1 ± 0.7%, and an elastic modulus of 70.5 ± 1.2 GPa. According to the potentiodynamic polarization and cell culture experiment, the (TiZrNb0.7)99.25O0.75 MEA exhibited superior corrosion resistance and biocompatibility, equivalent to the commercially pure titanium (CP-Ti). These findings provide a paradigm for achieving outstanding comprehensive properties in MEA via O doping.

materials science, multidisciplinary,chemistry, physical,metallurgy & metallurgical engineering
An Ultra‐Low Modulus of Ductile TiZrHfTa Biomedical High‐Entropy Alloys through Deformation Induced Martensitic Transformation/Twinning/Amorphization

Bingnan Qian,Xiaoqing Li,Yu Wang,Junhua Hou,Jikui Liu,Sihao Zou,Fengchao An,Wenjun Lu

DOI: https://doi.org/10.1002/adma.202310926

IF: 29.4

2024-03-08

Advanced Materials

Abstract:Biomedical alloys are paramount materials in biomedical applications, particularly in crafting biological artificial replacements. In traditional biomedical alloys, a significant challenge is simultaneously achieving an ultra‐low Young's modulus, excellent biocompatibility, and acceptable ductility. A multi‐component body‐centered cubic biomedical high‐entropy alloy (Bio‐HEA), which is composed of non‐toxic elements, is noteworthy for its outstanding biocompatibility and compositional tuning capabilities. Nevertheless, the aforementioned challenges still remain. Here, we propose a method to achieve a single phase with the lowest Young's modulus among the constituent phases by precisely tuning the stability of the body‐centered cubic phase in the Bio‐HEA. The subtle tuning of the body‐centered cubic phase stability also enables the induction of stress‐induced martensite transformation with extremely low trigger stress. The transformation‐induced plasticity and work hardening capacity were achieved via the stress‐induced martensite transformation. Additionally, the hierarchical stress‐induced martensite twin structure and crystalline‐to‐amorphous phase transformation provide robust toughening mechanisms in the Bio‐HEA. The cytotoxicity test confirmed that this Bio‐HEA exhibited excellent biocompatibility without cytotoxicity. In conclusion, our study provides new insights on the development of biomedical alloys with a combination of ultra‐low Young's modulus, excellent biocompatibility, and decent ductility. This article is protected by copyright. All rights reserved

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Bio-Corrosion Behaviors and Bio-Compatibilities of Tinbzrta and Tinbzrtamo High Entropy Alloys

Jun Cheng,Panyi Yang,Qiuming Chen,Xiao Long,Guang Chen,Jinming Xu,Wanyuan Gui,Tao Wu,Jian Hu

DOI: https://doi.org/10.1016/j.jmrt.2024.08.083

IF: 6.267

2024-01-01

Journal of Materials Research and Technology

Abstract:The bio-corrosion behavior and bio-compatibility of TiNbZrTa and TiNbZrTaMo high entropy alloys (HEAs) are crucial for their efficient maintenance during biological implantation. In this work, TiNbZrTa and TiNbZrTaMo HEAs were successfully prepared via vacuum melting, with a beta-type titanium alloy Ti35Nb7Zr5Ta, exhibiting good biocompatibility used as a comparison. Due to the high entropy effect of equal atomic ratios, both TiNbZrTa and TiNbZrTaMo HEAs exhibit body-centered cubic (BCC) structure and lattice distortion compared to the beta titanium alloy Ti35Nb7Zr5Ta. Mo elements contribute to the formation of a new BCC phase, resulting in a white matrix rich in Ta and Mo, and a dark second phase rich in Ti, Zr, and Nb. Electrochemical test results at 37 degrees C shown that TiNbZrTa has a wider and more stable passivation area than TiNbZrTaMo. The XPS results shown that formation of the passive film is related to the main elements added. Ti, Nb, Ta and Mo formed oxides via the solid-liquid interface and migrate inward, while Zr is formed at the passivation film/metal substrate interface and migrates outward, finally forming the layered structure of the passivation film. Additionally, the cytotoxicity test of mouse fiber cells was carried out to evaluate the biocompatibility of the HEAs. The results shown that the cell proliferation rate of TiNbZrTa and TiNbZrTaMo HEAs reached 0 and 1, respectively, with TiNbZrTa exhibiting better biocompatibility, as adding Mo reduced the cell proliferation rate. These findings may provide a method for predicting the bio-corrosion behavior and bio-compatibility of HEAs used for biological implantation.
A novel Ti42.5Zr42.5Nb5Ta10 multi-principal element alloy with excellent properties for biomedical applications

Zheng Li,Weiji Lai,Binbin Wang,Xin Tong,Deqiang You,Wei Li,Xiaojian Wang

DOI: https://doi.org/10.1016/j.intermet.2022.107731

IF: 4.075

2022-12-01

Intermetallics

Abstract:Body-centered cubic (BCC) Ti–Zr–Nb–Ta multi-principal element alloys (MPEAs) have drawn extensive research attention as orthopedic implant materials. In this work, a novel Ti42.5Zr42.5Nb5Ta10 multi-principal element alloy was developed for biomedical applications in terms of its microstructure, mechanical properties, wear performance, corrosion behavior, and in vitro biocompatibility. The Ti42.5Zr42.5Nb5Ta10 alloy after cold rolling followed by annealing at 880 °C (TZNT-880), possessed excellent mechanical properties combination, with a yield strength of 839.5 MPa, elongation at fracture of 22.6%, and Young's modulus of 63.2 GPa, superior to most of the currently existing biomedical BCC MPEAs. Meanwhile, TZNT-880 alloy exhibited higher wear resistance compared with commercial CP-Ti and Ti6Al4V, which is strongly related to its high H/E and H3/E2 values. Also, TZNT-880 alloy showed good corrosion resistance, as revealed by a nobler corrosion potential, lower corrosion current densities, and higher passivation stability, which is attributed to the formation of passivation films consisting of TiO2, ZrO2, Nb2O5, and Ta2O5. The in vitro biocompatibility tests demonstrated that the TiZrNbTa alloys can support cell adhesion and proliferation with high biocompatibility comparable to that of CP-Ti and Ti6Al4V, indicating their potential as a candidate for implant material.

materials science, multidisciplinary,chemistry, physical,metallurgy & metallurgical engineering
Design and Characterization of Selective Laser‐melted Ti6Al4V–5Cu Alloy for Dental Implants

Weian Zong,Song Zhang,Chunhua Zhang,Ling Ren,Qiang Wang

DOI: https://doi.org/10.1002/maco.202011650

2020-01-01

Materials and Corrosion

Abstract:Ti6Al4V–5Cu alloys have potential biomedical applications due to their adequate antibacterial properties. However, the wear and corrosion properties of these alloys are also crucial for dental implants. In the present study, Ti6Al4V–5Cu alloys were fabricated by selective laser melting (SLM). The microstructure and composition of Ti6Al4V–5Cu alloys by SLM were evaluated. The wear properties of the alloys in the simulated saliva environment and the atmospheric environment, as well as the electrochemical properties in the simulated saliva environment, were systematically investigated. The results showed that the crystal structure of Ti6Al4V–5Cu alloys was mainly composed of α‐Ti and Ti2Cu. In the SLM process, no preferred texture was observed due to the complex direction of the heat flux. The formation of Ti2Cu can improve the strength of the material and make the titanium copper alloy have higher microhardness. Ti6Al4V–5Cu alloy showed a satisfactory wear resistance in both wear media. The addition of Cu reduced the second‐phase content of the alloy. Meanwhile, the number of microcells was reduced, which was a positive factor to improve the corrosion resistance of the alloys.
Microstructure and Mechanical Properties of Biomedical Ti-Zr-Nb-Ta-Sn High-Entropy Alloys

Maxim Ozerov,Nikita Yurchenko,Vitaly Sokolovsky,Elena Nozdracheva,Evgeniya Panina,Sergey Nadezhdin,Nikita Stepanov,Sergey Zherebtsov

DOI: https://doi.org/10.3390/met13020353

IF: 2.695

2023-02-11

Metals

Abstract:Ti(50-x)Zr38NbxTa8Sn4 high-entropy alloys with x = 0, 10, and 20 at.% were produced by vacuum arc melting in a high-purity argon atmosphere. The initial microstructures consisted of equiaxial bcc grains with sizes of 115 ± 30 μm, 250 ± 60 μm, and 280 ± 70 μm for the Ti30Nb20, Ti40Nb10, and Ti50Nb0 alloys, respectively. The Ti30Nb20 and Ti40Nb10 alloys showed untypical mechanical behavior with a short strain-hardening stage followed by a gradual decrease in flow stress after reaching the yield point. Although these two alloys had some inclination toward macroscopic strain localization, their tensile elongation was similar to that obtained in the Ti50Nb0 alloy, which had a more extended stage of uniform deformation. The differences were associated with distinct microstructures observed after deformation to fracture. The formation of dislocation bands and the activation of cross-slip at the microscale, as well as the appearance of kink bands at the mesoscale, can result in plastic instability. In contrast, a lamellar-like microstructure with parallel dislocation bands, such as the one observed in the Ti50Nb0 alloy, can ensure a more stable mechanical behavior. The developed alloys (Ti30Nb20 and Ti40Nb10) have properties that make them highly attractive for biomedical application due to a combination of very high yield strengths (1090 and 930 MPa, respectively), low Young's moduli (~78 and ~69 GPa, respectively), reasonable ductility, and excellent biocompatibility.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Design and Fabrication of a 5Ti5Zr5Nb1Sn High‐Entropy Alloy as Metallic Biomedical Material

Zhenwei Liu,Pei Liu,Wei Yue,Aiqin Wang,Jingpei Xie

DOI: https://doi.org/10.1002/adem.202200068

IF: 3.6

2022-03-23

Advanced Engineering Materials

Abstract:Herein the present work, the thermodynamic, physical, and mechanical properties of different random solid solution structure models are first calculated based on first‐principles calculation method, and the optimal composition ratio of 5Ti5Zr5Nb1Sn is quickly selected as a new biomedical high‐entropy alloy (HEA) with a low elastic modulus and high strength–ductility balance. Then, 5Ti5Zr5Nb1Sn HEA is prepared by vacuum‐melting method. The microstructure characterization results show that the actual composition of 5Ti5Zr5Nb1Sn HEA corresponds to the calculated target composition, and the HEA consists of two phases BCC1 and BCC2 with distinct color and structure. The compressive yield strength and compressive elongation of the 5Ti5Zr5Nb1Sn HEA are 1171.2 MPa and 29.03%, respectively. The compressive elastic modulus is 22.4 GPa, which is within the range of human bone elastic modulus (10–30 GPa). There are many tiny dimples and small tearing edges in the compression fracture, showing obvious plastic deformation characteristics. The analysis results of potentiodynamic polarization curve show that the corrosion resistance of 5Ti5Zr5Nb1Sn HEA is equivalent to that of pure titanium. Therefore, 5Ti5Zr5Nb1Sn HEA possesses the characteristics of high strength and ductility, low elastic modulus, and excellent corrosion resistance, and has the potential to be used as metallic biomedical materials. 5Ti5Zr5Nb1Sn high‐entropy alloy (HEA) is designed as metallic biomedical material by first‐principles calculation. The 5Ti5Zr5Nb1Sn HEA consists of two phases BCC1 and BCC2 with distinct color and structure. Compressive yield strength and compressive elongation of 5Ti5Zr5Nb1Sn HEA are 1171.2 MPa and 29.03%, respectively. The 5Ti5Zr5Nb1Sn HEA exhibits compressive elastic modulus of 22.4 GPa and manifests excellent corrosion resistance.

materials science, multidisciplinary
Microstructural, Mechanical, and Electrochemical Characterization of CrMoNbTiZr High-Entropy Alloy for Biomedical Application

Akeem Akinwekomi,Farid Akhtar

DOI: https://doi.org/10.3390/ma16155320

2023-07-28

Abstract:High-entropy alloys (HEA) with superior biocompatibility, high pitting resistance, minimal debris accumulation, and reduced release of metallic ions into surrounding tissues are potential replacements for traditional metallic bio-implants. A novel equiatomic HEA based on biocompatible metals, CrMoNbTiZr, was consolidated by spark plasma sintering (SPS). The relative sintered density of the alloy was about 97% of the theoretical density, indicating the suitability of the SPS technique to produce relatively dense material. The microstructure of the sintered HEA consisted of a BCC matrix and Laves phase, corresponding to the prediction of the thermodynamic CALPHAD simulation. The HEA exhibited a global Vickers microhardness of 531.5 ± 99.7 HV, while the individual BCC and Laves phases had hardness values of 364.6 ± 99.4 and 641.8 ± 63.0 HV, respectively. Its ultimate compressive and compressive yield strengths were 1235.7 ± 42.8 MPa and 1110.8 ± 78.6 MPa, respectively. The elasticity modulus of 34.9 ± 2.9 GPa of the HEA alloy was well within the range of cortical bone and significantly lower than the values reported for commonly used biomaterials made from Ti-based and Cr-Co-based alloys. In addition, the alloy exhibited good resistance to bio-corrosion in PBS and Hanks solutions. The CrMoNbTiZr HEA exhibited an average COF of 0.43 ± 0.06, characterized mainly by abrasive and adhesive wear mechanisms. The CrMoNbTiZr alloy's mechanical, bio-corrosion, and wear resistance properties developed in this study showed a good propensity for application as a biomaterial.
Additively manufactured high entropy alloy with high wear resistance for biomedical implant

Cijun Shuai,Jiading Xie,Xihao Jiang,Shuping Peng,Chunming Wang

DOI: https://doi.org/10.1016/j.vacuum.2023.112939

IF: 4

2023-12-30

Vacuum

Abstract:Titanium and its alloys play a vital role as implant materials in orthopedic and dental surgery. However, its poor wear resistance limits its application in the medical field. High entropy alloy (HEA) has high wear resistance due to the combined action of high entropy, lattice distortion, and cocktail effects. In this work, TiFeCrCoNi HEA is prepared by Laser powder bed fusion (LPBF) under the protection of high pure Ar gas . The results show the TiFeCrCoNi HEA has mainly FCC phase and a small amount of Hexagonal and Laves phases . Its microhardness is up to 776.3 ± 21.4 H V and is 2.8 times that of pure Ti. Meanwhile, the HEA has a low friction coefficient of 0.1–0.15, which is attributed to high hardness precipitates and grain refinement. The main wear mechanism of the HEA is oxidation wear, adhesive wear , and abrasive wear. In addition, the TiFeCrCoNi HEA also demonstrates good biocompatibility.

materials science, multidisciplinary,physics, applied

Ultrasound assisted extraction of phenolic compounds from grapes.

Development and properties of dental Ti–Zr binary alloys

Ti-Zr-Nb-Ta-Sn Medium-Entropy Alloys with Excellent Properties as Potential Biomaterials

New TiTaNbZrMo high-entropy alloys for metallic biomaterials

Investigations on microstructure and properties of Ti-Nb-Zr medium-entropy alloys for metallic biomaterials

Biocompatible As-Cast and Homogenized TiNbTaZrMoV High Entropy Alloys: Mechanical Properties, Corrosion Resistance and in Vitro Studies

Development of non-equiatomic Bio-HEAs based on TiZrNbTa-(Mo and Mn)

Experimental and DFT Investigations of AlNbTiVZr High Entropy Alloys with Excellent Mechanical Properties

Design and properties of novel Ti–Zr–Hf–Nb–Ta high-entropy alloys for biomedical applications

Structure and properties of Ti-rich Ti–Zr–Nb–Mo medium-entropy alloys

A Review: Design from Beta Titanium Alloys to Medium-Entropy Alloys for Biomedical Applications

CASP9 results compared to those of previous casp experiments

Achieving superior mechanical properties and biocompatibility in an O-doping TiZrNb medium entropy alloy

An Ultra‐Low Modulus of Ductile TiZrHfTa Biomedical High‐Entropy Alloys through Deformation Induced Martensitic Transformation/Twinning/Amorphization

Bio-Corrosion Behaviors and Bio-Compatibilities of Tinbzrta and Tinbzrtamo High Entropy Alloys

A novel Ti42.5Zr42.5Nb5Ta10 multi-principal element alloy with excellent properties for biomedical applications

Design and Characterization of Selective Laser‐melted Ti6Al4V–5Cu Alloy for Dental Implants

Microstructure and Mechanical Properties of Biomedical Ti-Zr-Nb-Ta-Sn High-Entropy Alloys

Design and Fabrication of a 5Ti5Zr5Nb1Sn High‐Entropy Alloy as Metallic Biomedical Material

Microstructural, Mechanical, and Electrochemical Characterization of CrMoNbTiZr High-Entropy Alloy for Biomedical Application

Additively manufactured high entropy alloy with high wear resistance for biomedical implant