Abstract:This present study mainly focuses on the influence of low-calcium circulating fluidized bed fly ash (LCFA) on the mechanical property and microstructure of cement-based materials under different curing conditions. The mechanical properties test was conducted by changing variable parameters, such as LCFA content, the internal mixing ratio of LCFA and fly ash (FA), and dry and water curing conditions. Further, the hydration products and pore structure were analyzed using XRD, FT-IR, TG-DTG, NI, SEM, and BET micro-testing technology. The strength development law of LCFA on cement-based materials is discussed. The research results show that LCFA has a certain degree of self-hardening and can be used as a cementitious material in cement-based materials. Still, the loose and porous microstructure of LCFA leads to higher water requirements, which reduces the fluidity of cement-based pastes. Water curing is favorable for promoting the development of LCFA on the long-term compressive strength of cement-based materials. When the LCFA was added to the cement, the optimal substitution ratio was 20%, and the compressive strength at 91 days reached 101 MPa. In the case of compounding LCFA and FA, when the internal mixing ratio of LCFA/FA was 3 and the total content was 20%, the mechanical properties were the highest, and the compressive strength at 91 days was 92 MPa. The microscopic analysis result shows that the cumulative hydration heat of the samples decreased significantly with the increase of dosage of LCFA. The main hydration products of cement-based materials mixed with LCFA were AFt, C-S-H gel, and Ca(OH)2. AFt and C-S-H gels are critical to the strength development of OPC-LCFA samples. The active Al2O3 and active SiO2 in LCFA were involved in hydration reactions to promote the formation of C-A-H and C-S-H gel and effectively promote the development of the mechanical properties. Overdosages of LCFA would reduce the ettringite formation rate. FA is not conducive to AFt formation in the hydration process of OPC-FA samples.

Temperature-Dependent Hydration and Mechanical Properties of High-Volume Fly Ash Cement with Chemical Additives

Hydration and Mechanical Properties of High-Volume Fly Ash Cement under Different Curing Temperatures

Strength and Microstructural Characteristics of Activated Fly Ash–Cement Paste

Investigation of Low-Calcium Circulating Fluidized Bed Fly Ash on the Mechanical Strength and Microstructure of Cement-Based Material

Utilization of fly ash microsphere powder as a mineral admixture of cement: Effects on early hydration and microstructure at different curing temperatures

Hydration and Mechanical Properties of High-Volume Fly Ash Concrete with Nano-Silica and Silica Fume

Effects of Fly Ash Particle Size and Chemical Activators on the Hydration of High-Volume Fly Ash Mortars

Properties of CO 2 -cured cement incorporating fly ash and slag subjected to further water curing

Investigating the Hydration, Mechanical Properties, and Pozzolanic Activity of Cement Paste Containing Co-Combustion Fly Ash

Influence of Calcined Flue Gas Desulfurization Gypsum and Calcium Aluminate on the Strength and AFt Evolution of Fly Ash Blended Concrete under Steam Curing

How Competitive Hydration between C 3 A and C 3 S in the Fast Dissolution Stage Affects the Hydration of Low-Heat Portland Cement Blended Pastes

Investigating the Impact of Fly Ash on the Strength and Micro-Structure of Concrete during Steam Curing and Subsequent Stages

Study on Mechanical and Microscopic Properties of Fly Ash Cement-Based Materials in High Geothermal Environment

Research on Hydration Degree of Cement-Fly Ash Complex Binders

Mechanical and microstructural performances of fly ash blended cement pastes with mixing CO2 during fresh stage

Effects of Na2CO3/Na2SiO3 Ratio and Curing Temperature on the Structure Formation of Alkali-Activated High-Carbon Biomass Fly Ash Pastes

Microstructure and phase characterizations of fly ash cements by alkali activation

Influence of fly ash on mechanical properties and hydration of calcium sulfoaluminate-activated supersulfated cement

Hydration, mechanical properties and durability of high-strength concrete under different curing conditions

Effect of fly ash on the atomic scale structure of C–S–H during Portland Cement hydration

Influence Mechanism of Initial Concreting Temperature and Water-Binder Ratio on Hydration Rate of Fly Ash Concrete