Abstract:The overall energy density of the Li-ion batteries depends on the operation voltage and the theoretical capacity of the electrodes. Theoretical capacity of layered lithium cobalt oxide (Li 1-x CoO 2 ) cathode is 274 mAh/g, which is higher than the many other commercially available cathode materials, including lithium manganese oxide (148 mAh/g) and lithium iron phosphate (170 mAh/g). However, the irreversible chemo-mechanical deformations at deep charge condition (x>0.5) at high voltages (>4.2V) presents harvesting its full theoretical capacity. Previous XRD and NMR studies demonstrated the structural collapse of the material at deep charge condition [1]. A various material-based strategies such as doping and surface coating have been utilized to improve the stability of the LCO cathodes at deep charge conditions [2]. However, the governing forces behind the chemo-mechanical instabilities in LCO cathodes at high voltages are still poorly understood. In this study, our goal is to elucidate the electrochemically-driven mechanical deformations in the LCO cathode during Li-ion intercalation. To achieve it, we performed in situ curvature measurement and digital image correlation measurements to probe stress and strain evolution in the electrode while cycling the battery. The combination of these techniques previously provided information about the interfacial and structural deformations in LiFePO 4 and LiMn 2 O 4 [3,4]. Here, free-standing composite LCO electrodes were fabricated for strain measurements. Thin film LCO electrode was prepared using chemical vapor deposition method on a silicon wafer for stress measurements. The electrodes were cycled in 1 M LiClO 4 in 1:1 EC:DMC electrolyte against Li counter electrode. The upper limit of the charge voltage were varied from 4.2 to 4.5V periodically in order to investigate the deformations at deep charge state. Strain and stress derivatives were calculated with respect to applied potential in order to understand the potential-dependent mechanical deformations in the LCO electrode. In this talk, we will present the impact of the structural and interfacial deformations on the chemo-mechanical instabilities of LCO cathodes. Acknowledgment: This work was supported by the U.S. Department of Energy, Office of Science, Basic Energy Sciences (Award numberDE-SC0021251). We are also grateful for Dr. Gabriel Veith for fabricating thin film LCO cathodes. References [1] J. Li, C. Lin, M. Weng, Y. Qiu, P. Chen, K. Yang, W. Huang, Y. Hong, J. Li, M. Zhang, C. Dong, W. Zhao, Z. Xu, X. Wang, K. Xu, J. Sun, F. Pan, Structural origin of the high-voltage instability of lithium cobalt oxide, Nat. Nanotechnol. 16 (2021) 599–605. https://doi.org/10.1038/s41565-021-00855-x. [2] L. Wang, B. Chen, J. Ma, G. Cui, L. Chen, Reviving lithium cobalt oxide-based lithium secondary batteries-toward a higher energy density, Chem. Soc. Rev. 47 (2018) 6505–6602. https://doi.org/10.1039/c8cs00322j. [3] Ö.Ö. Çapraz, K.L. Bassett, A.A. Gewirth, N.R. Sottos, Electrochemical Stiffness Changes in Lithium Manganese Oxide Electrodes, Adv. Energy Mater. 7 (2017). https://doi.org/10.1002/aenm.201601778. [4] K.L. Bassett, Ö. Özgür Çapraz, B. Özdogru, A.A. Gewirth, N.R. Sottos, Cathode/Electrolyte Interface-Dependent Changes in Stress and Strain in Lithium Iron Phosphate Composite Cathodes, J. Electrochem. Soc. 166 (2019) A2707–A2714. https://doi.org/10.1149/2.1391912jes.

Shakedown, Ratcheting and Fatigue Analysis of Cathode Coating in Lithium-Ion Battery under Steady Charging-Discharging Process

On the Study of Cyclic Plasticity Behaviour of Primary Electrode Particle for Lithium-Ion Battery

Unravelling the Impact of Reaction Paths on Mechanical Degradation of Intercalation Cathodes for Lithium-Ion Batteries.

Numerical Analysis of the Cyclic Mechanical Damage of Li-ion Battery Electrode and Experimental Validation

Bulk Fatigue Induced by Surface Reconstruction in Layered Ni-rich Cathodes for Li-ion Batteries

Multi-scale Failure Behavior of Cathode in Lithium-ion Batteries Based on Stress Field

Stable Interstitial Layer to Alleviate Fatigue Fracture of High Nickel Cathode for Lithium-Ion Batteries

Improving LiNi0.9Co0.08Mn0.02O2’s Cyclic Stability Via Abating Mechanical Damages

Mitigation of Charge Heterogeneity by Uniform in Situ Coating Enables Stable Cycling of LiCoO2 at 4.6V

Theoretical Understanding and Experimental Suppression of the Capacity Degradation of Ni-Rich Layered Oxide Cathode Materials for Li Ion Battery

Probing Particle-Carbon/Binder Degradation Behavior in Fatigued Layered Cathode Materials through Machine Learning Aided Diffraction Tomography

Chemo-Mechanical Deformations in Lithium Cobalt Oxide Cathode during Li-Ion Intercalation

High‐Voltage Charging‐Induced Strain, Heterogeneity, and Micro‐Cracks in Secondary Particles of a Nickel‐Rich Layered Cathode Material

Understanding the Degradation Mechanisms of Lithium Ion Batteries Using in-Situ Multi-Scale Diffraction Techniques

Insights into Capacity Fading Mechanism and Coating Modification of High-Nickel Cathodes in Lithium-Ion Batteries

Operando chemo-mechanical evolution in LiNi0.8Co0.1Mn0.1O2 cathodes

Deformation and Failure of Lithium-Ion Batteries Treated As a Discrete Layered Structure

Anisotropic Strain Evolution of Layered LiNi0.5Co0.2Mn0.3O2 Cathode in Formation Cycle

Mechanical Behavior Analysis of High Power Commercial Lithium-Ion Batteries

Stress Evolution in Lithium-ion Composite Electrodes during Electrochemical Cycling and Resulting Internal Pressures on the Cell Casing

Coupled effects of charge–discharge cycles and rates on the mechanical behavior of electrodes in lithium–ion batteries