Abstract:Advanced Li-ion batteries adopting new cathode chemistries are required for the successful widespread transition to electric vehicles (EVs) and renewable energy sources, aiming for high energy density, long cycle life, and good rate capability. Commercial candidates for EV batteries include Ni-rich Li(Ni x Mn y Co 1−x-y )O 2 (NMC) cathodes, with Ni:Mn:Co ratios of 8:1:1 (NMC811) and higher. These are favored because of their high specific capacity (~ 200 mAh g -1 )and reduced cobalt content. Despite all of the advantages, these materials suffer from a range of degradation modes, many of which are associated with the redox and crystallographic behavior at high states of charge. In particular, Ni-rich cathodes suffer from several limitations, such as rapid capacity fade in comparison to NMC stoichiometries with lower Ni content. In addition, they also have a lower onset voltage for oxygen release and subsequent surface reconstruction leading to the formation of spinel and rock salt phases which impede (de)lithiation and therefore the achievable capacity of the cell. 1 Crystallographic properties of electrode materials are intrinsically linked to the electrochemical performance of the cell. NMC materials suffer from anisotropic changes in the crystal structure during cycling which induces strain and leads to issues such as crack formation, expediting degradation. One method to tackle capacity fade is to switch to single-crystal morphologies (particle size 1-3 μm) which have better mechanical stability than conventional polycrystalline morphologies (secondary agglomerate particles ~ 10 μm made up of primary particles which are 100 nm – 1 μm in size) and have less propensity to form extensive rock-salt layers. It is thought that the single-crystal morphology helps to reduce stress in the material as the anisotropic stress in polycrystalline cathodes is concentrated at grain boundaries. However, there is still a limited understanding of the subtle mechanistic differences between the two materials during cycling. 2 A multi-scale approach is required to gain a more comprehensive understanding of the degradation mechanisms at play and how they initiate and propagate. In this work, synchrotron diffraction methods were employed at the crystal, particle and cell scale using a variety of techniques including in-situ Bragg Coherent Diffraction Imaging (BCDI), 3D-XRD and operando high-resolution XRD. Intra-particle, inter-particle and electrode level heterogeneities were observed during cycling, both in pristine and aged samples. It is believed that these heterogeneities accelerate the loss of performance at the cell level by inducing crack formation which can then be observed in X-ray computed tomography data acquired in simultaneous lab studies. The overarching goal of these investigations is to add to the understanding of complex degradation mechanisms for Ni-rich layered transition metal oxide cathodes, ultimately aiding in the informed development of future battery electrode materials. References: 1] Xu, C. et al., Phase Behaviour during Electrochemical Cycling of Ni‐Rich Cathode Materials for Li‐Ion Batteries. Adv. Energy Mater. 2021, 11, 2003404. 2] Yin, S. et al., Fundamental and solutions of microcracks in Ni-rich layered oxide cathode materials of lithium-ion batteries. Nano Energy, 2021, 83, 105854.

Coupled effects of charge–discharge cycles and rates on the mechanical behavior of electrodes in lithium–ion batteries

Deterioration of Lithium Iron Phosphate/graphite Power Batteries under High-Rate Discharge Cycling

Extended Cycle Life Implications of Fast Charging for Lithium-Ion Battery Cathode

Electrochemo‐Mechanical Effects on Structural Integrity of Ni‐Rich Cathodes with Different Microstructures in All Solid‐State Batteries

Low-Temperature Aging Effect on Safety of Lithium-Ion Batteries Subjected to Intrusion: A Comparative Study of 18650 and Pouch Cells

Phase Behavior during Electrochemical Cycling of Ni‐Rich Cathode Materials for Li‐Ion Batteries

Thickness effect on the mechanical performance of cathodes in lithium-ion batteries

Nickel-rich Nickel Manganese Cobalt (NMC622) Cathode Lithiation Mechanism and Extended Cycling Effects Using Operando X-ray Absorption Spectroscopy

Thickness variation of lithium metal anode with cycling

Abuse Tolerance Behavior Of Layered Oxide-Based Li-Ion Battery During Overcharge And Over-Discharge

Balancing interfacial reactions to achieve long cycle life in high-energy lithium metal batteries

Quantifying the Impact of Charge Rate and Number of Cycles on Structural Degeneration of Li-Ion Battery Electrodes

Impacts of vibration and cycling on electrochemical characteristics of batteries

Experimental and Modeling Analysis of Mechanical Response of Composite Electrodes in Lithium Batteries

Different mechanical and electrochemical behavior between the two major Ni-rich cathode materials in Li-Ion batteries

Understanding the Degradation Mechanisms of Lithium Ion Batteries Using in-Situ Multi-Scale Diffraction Techniques

Unravelling and Quantifying the Aging Processes of Commercial Li(Ni0.5Co0.2Mn0.3)O2/Graphite Lithium-ion Battery under Constant Current Cycling

Effects of Different Charging and Discharging Modes on Thermal Behavior of Lithium Ion Batteries

Deformation and failure behaviors of anode in lithium-ion batteries: Model and mechanism

The Effect of Structure and Mechanical Properties Change of Current Collector during Cycling on Sb-Based Lithium-Ion Batteries' Performance

Capacity Fading Mechanism of the Commercial 18650 LiFePO4-Based Lithium-Ion Batteries: an in Situ Time-Resolved High-Energy Synchrotron XRD Study