Abstract:Due to its extensive application, the safety issue of lithium-ion battery has received increasing attention. For crashworthiness design of battery in electric vehicles, it is of great importance to investigate the response of the battery under mechanical loading and understand the mechanism of internal short circuit. Quasi-static and intermediate strain rate uniaxial tension tests were conducted on the electrodes and the separators. The high speed camera and DIC (digital image correlation) method were adopted to measure the strain while a self-design load cell was used to measure force in dynamic test. Either loading velocity or loading direction was varied in different tests. The upper limit of the test strain rate achieved 66 /sec. All the component materials showed strain rate dependency and separators demonstrated noticeable anisotropy. Quasi-static penetration tests were conducted on two different types of pouch cell using steel and plastic punch heads. For both Type A pouch cell and Type B pouch cell, during penetration process using plastic punch head, no significant voltage drop or temperature rise was observed. During penetration process using steel punch head, only Type A pouch cell produced short circuit. When the punch head was removed, the voltage of the cells could recover to certain level. From post mortem examination, it was found that for a single pouch cell, all the electrodes presented the same fracture mode that the stacked anode and cathode formed several fragments in the penetration path, while the separators in between only formed a central crack when the punch head went through. Since the separators had a larger elongation ratio than the electrodes, the extended separators around the rupture location could block the direct and constant contact between anode and cathode, electrodes and steel punch, which explained why no massive internal short circuit was initiated. The drop tower was used to conduct dynamic penetration test. The results indicated that under dynamic loading, internal short circuit was more likely to be triggered which can be explained by the strain rate effect of the separators. This study highlighted the importance of the separator to the safety performance of pouch cells.

Deformation and Failure of Lithium-Ion Batteries Treated As a Discrete Layered Structure

A Large Deformation and Fracture Model of Lithium-Ion Battery Cells Treated As a Homogenized Medium

Mechanical Deformation of Lithium-Ion Pouch Cells under In-Plane Loads-Part I: Experimental Investigation

Prediction of Shear Crack Formation of Lithium-Ion Batteries under Rod Indentation: Comparison of Seven Failure Criteria

Constitutive Behavior and Mechanical Failure of Internal Configuration in Prismatic Lithium-Ion Batteries under Mechanical Loading

Investigation of the Deformation Mechanisms of Lithium-Ion Battery Components Using In-Situ Micro Tests

Fracture Mode Analysis of Lithium-Ion Battery under Mechanical Loading

Mechanical Modeling and Testing of Pouch Cells under Various Loading Conditions

Volume Deformation Of Large-Format Lithium Ion Batteries Under Different Degradation Paths

Stress and Strain Characterization for Evaluating Mechanical Safety of Lithium-Ion Pouch Batteries under Static and Dynamic Loadings

Crushing Behavior Of Vehicle Battery Pouch Cell And Module: A Combined Experimental And Theoretical Study

Comprehensive investigation on the durability and safety performances of lithium-ion batteries under slight mechanical deformation

Mechanical Damage in a Lithium-Ion Pouch Cell under Indentation Loads

Stress Analysis of Electrochemical and Force-Coupling Model for Ternary Lithium-Ion Batteries

Deformation and Failure Properties of Lithium-Ion Battery Under Axial Nail Penetration

Inhomogeneous Degradation Induced by Lithium Plating in a Large-Format Lithium-Ion Battery

Progressive Degradation Behavior and Mechanism of Lithium-Ion Batteries Subjected to Minor Deformation Damage

Constitutive Behavior and Progressive Mechanical Failure of Electrodes in Lithium-Ion Batteries

Microstructural Deformation Patterns of a Highly Orthotropic Polypropylene Separator of Lithium-Ion Batteries: Mechanism, Model, and Theory

Decoupling the Influence of Impact Energy and Velocity on Dynamic Failure of Cylindrical Lithium-Ion Batteries

Mechanical testing and macro-mechanical finite element simulation of the deformation, fracture, and short circuit initiation of cylindrical Lithium ion battery cells