Abstract:The traditional subtractive process to fabricate conductive patterns is environmentally harmful, wasteful, and limited in line width. The additive process, including direct printing of conductive paste or ink, direct printing of catalytic ink, laser-induced forward transfer, etc., can solve these problems. However, the current additive process also faces many difficulties such as low electrical and adhesion properties, low pattern thickness, high cost, etc. Benzotriazole (BTA), as widely used corrosion inhibitor, can be adsorbed onto a copper surface. The electroplated copper film on BTA-adsorbed copper foil shows poor adhesion. On the basis of this phenomenon, a novel template transfer process to additively fabricate conductive patterns has been developed. A permeant antiadhesive mask is printed on carrier copper foil, and then, BTA is adsorbed onto the exposed area of the carrier foil, thus forming the template. The template is electroplated to grow conductive patterns in the exposed parts, and then can be adhered to the flexible substrate. The substrate is peeled off, with the transfer of the conductive patterns to the substrate, to form the designed conductive patterns on PET. By reimmersing the template into BTA solution, the template can be used again. The mechanism of BTA adsorption and the reason for the low peeling strength are researched using Raman spectra, XPS and electrochemical impedance spectroscopy. Copper patterns more than 20 μm in thickness can be prepared on PET, the resistivity of the prepared copper patterns is 2.01 μΩ cm, which is about the same as bulk copper, and the peeling strength of the pattern on PET is measured to be 6.97 N/cm. This template transfer process, with no waste, low pollution, high electrical and adhesion properties, and low cost, shows high potential in the large scale manufacturing of electronic devices, such as RFID circuitry, FPCs, etc.

Fabrication of flexible copper patterns by electroless plating with copper nanoparticles as seeds

Fabrication of copper patterns on flexible substrate by patterning-adsorption-plating process.

Site-selective Fabrication of Patterned Transparent Copper Mesh on Flexible Substrates at Mild Temperature for Green, Low Cost Electronics

Preparation of Selective Conductive Copper Patterns by Pen-on-paper Writing Combined with Electroless Plating

PET Surface Modification with Inkjet-Printing Pd 2+ /Epoxy Resin Solution for Selective Electroless Copper Plating

The Pseudoenzyme PDX1.2 Boosts Vitamin B6 Biosynthesis under Heat and Oxidative Stress in Arabidopsis*

Fabrication of User-Defined Copper Conductive Patterns Onto Paper Substrate for Flexible Electronics by Combining Wax Patterning with Electroless Plating

Fabrication of dual-side metal patterns onto textile substrates for wearable electronics by combining wax-dot printing with electroless plating

Additive Fabrication of Conductive Patterns by A Template Transfer Process Based on Benzotriazole Adsorption As A Separation Layer

A facile process to fabricate metal coating on PET sheet: Preparation of highly active polymer brush/Ag particle and its application in electroless copper plating

Directly Electroplated Metallization on Flexible Substrates Based on Silver Nanowire Conductive Composite for Wearable Electronics

Ingenious Method for Rapid Fabrication of a Highly Conductive Hybrid Film of Printed Cu Nanoparticle Layers Plated by Ag Nanoplates on a PET Substrate at Room Temperature

Electroless Copper Plating on 1,2-Ethylenediamine Grafted Poly(ethyleneterepthalate) for the Fabrication of Flexible Copper Clad Laminate

A facile process to fabricate electroless plating on PET sheet: Effects of surface roughness on adhesive force, electronic and structural properties of copper coating

Fabrication of selective electroless copper plating on PET sheet: Effect of PET surface structure on resolution and adhesion of copper coating

A Facile Fabrication Method of Silver Lines on PET with Good Adhesion at Room Temperature

Epoxy Resin-Assisted Cu Catalytic Printing for Flexible Cu Conductors on Smooth and Rough Substrates

Fabrication of Flexible Copper Microelectrodes Using Laser Direct Writing for Sensing Applications

Fabrication of Conductive Copper Patterns Using Photocatalyst-activated Electroless Deposition

Unraveling the Mechanism of Plasma‐Induced Curing of Particle‐Free Complex Inks for Manufacturing of High‐Performance Flexible Copper Films and Patterns

3D Porous Polysiloxane Ion-Adsorption Films for Additive Fabrication of Conductive Patterns with High Adhesion