Abstract:WC–Co cemented carbides are a class of hard composite materials of great technological importance. They are widely used as tool materials in a large variety of applications that have high demands on hardness and toughness, including mining, turning, cutting and milling. The HVOF (high velocity oxygen fuel) technology has been very successful in spraying wear resistant WC–Co coatings with higher density, superior bond strengths and less decarburization than many other thermal spray processes, attributed mainly to its high particle impact velocities and relatively low peak particle temperatures. The degree of decomposition and bond strength is directly related to relevant particle parameters such as velocity, temperature and state of melting or solidification. These are consecutively related to process parameters such as powder particle size distribution, carrier gas flow rate, and fuel type employed. To obtain detailed particle data important for thermal spraying, mathematical models are developed in the present paper to predict the particle dynamic behavior in a liquid fuelled HVOF thermal spray gun. The particle transport equations are coupled with the three-dimensional, chemically reacting, turbulent gas flow, and solved in a Lagrangian manner. The melting and solidification within the particles as a result of heat exchange with the surrounding gas flow is solved numerically. The in-flight characteristics of WC–Co particles are studied and the effects of carrier gas parameters on particle behavior are examined. The results demonstrate that WC–Co particles smaller than 5μm in diameter undergo melting and solidification prior to impact while most particles never reach liquid state during the HVOF thermal spraying. The flow rate of carrier gas has considerable influence on particle dynamics as well as deposition on substrate. At higher flow rate the powder particles are redirected further away from the substrate center, while smaller flow rate results in better heating, higher impact velocity and deposition closer to the substrate center.

Physical property effect of powder on thermal spraying coatings

Thermal sprayed WC-Co coatings and their mechanical properties

Effects Of Wc Crystal Characteristics On Microstructure And Mechanical Property Of Hvof-Sprayed Wc-Cocr Coatings

Influence of Powder Porous Structure on the Deposition Behavior of Cold-Sprayed Wc-12co Coatings

Study on Properties of Coatings Prepared by Supersonic Plasma Spraying with Three Kinds of WC-12Co Powder

Influence of Spray Parameters on Sliding Wear Properties of HVOF Sprayed Fe-Based Amorphous Coatings

Effects of structure and processing technique on the properties of thermal spray WC–Co and NiCrAl/WC–Co coatings

Characterization on microstructures and properties of WC-CoCr coating deposited by HVAF and HVOF processes

Effect of the Powder Particle Structure and Substrate Hardness During Vacuum Cold Spraying of Al2O3

Influence of Powder Structure on the Micro-Hardness and Fracture Toughness of Cold-Sprayed WC-12Co Deposit

Influences Of Agglomeration Powder Preparation On Deposition Of Cold-Sprayed Ti2alc Coating

Influence of WC Particle Size on the Mechanical Properties and Residual Stress of HVOF Thermally Sprayed WC–10Co–4Cr Coatings

Correlation study of random deposition for WC–12Co multiparticles on the TC18 substrates

Analysis of Microstructure of WC-12Co Coatings Prepared by the Three Kinds of Supersonic Thermal Spraying Processes

Research on flame characteristics and coating growth process of titanium alloy in HVAF spraying

Influence of Hard Phase on the Properties of Cold-Sprayed FeAl Intermetallic Compound Coatings

Comparison of the Mechanical and Electrochemical Properties of WC-25Co Coatings Obtained by High Velocity Oxy-Fuel and Cold Gas Spraying

Microstructure and mechanical property of high velocity oxy-fuel sprayed WC-Cr3C2-Ni coatings

Microstructure Characterization and Abrasive Wear Performance of Hvof Sprayed Wc-Co Coatings

Influence of heat treatment on surface properties of HVOF deposited WC and Ni-based powder coatings: a review

Computational Simulation of Thermally Sprayed WC–Co Powder