Abstract:Al-Zn-Mg-Cu alloy, as an important lightweight structural material in the aerospace field, has ushered in a broader application space and proposed higher performance requirements. This paper presents the experimental investigation of the effect of Zr content on the microstructure refinement and performance improvement of cast Al-5.8Zn-2.3Mg-1.7Cu alloy, aiming to optimize the additional amount of Zr, refine the alloy grains, and improve the microstructure uniformity and mechanical properties. The chemical component, phase, and microstructure were observed by inductively coupled plasma, X-ray diffraction, optical microscope and scanning electron microscope; the hardness and mechanical properties were measured by Brinell hardness tester and tensile testing machine. The addition of different contents of Zr into the alloy can form fine dispersed or primary coarse Al3Zr phase, which has a significant effect on the microstructure and mechanical properties of the alloy. The results indicate that the addition of 0.05 wt% Zr does not significantly improve the grain refinement and mechanical properties, but the Brinell hardness reaches the maximum. As the Zr content rises, the grain refinement effect becomes more obvious, while the mechanical properties first increase and then decrease. The addition amount reaches 0.20 wt%, the second dendrite arm spacing is the smallest, the ultimate tensile strength, yield strength and elongation at room temperature reach the maximum of 296.74 MPa, 249.41 MPa and 8.26%, respectively. When the amount of Zr added exceeds 0.20 wt%, the existence of coarse and brittle primary Al3Zr phase reduces the mechanical properties, and the fracture morphology changes from ductile to brittle intergranular fracture.

Effect of ZrC Particle on Grain Refining and Properties of Low-Carbon and Low-Alloy Steel

Effect of Adding Ceramic Particles on Grain Refining in Low Carbon Microalloy Steel

Strengthening Effect of ZrC Particles on Low-Carbon Microalloy Steel

Effect of Quenching Process on the Microstructure and Mechanical Property of 20mn2 Steel Containing ZrC Particles

Effects of Deforming Temperature on Grain-refining of 20Mn2 Steel Containing ZrC Particles

Effect of Trace Zr on Microstructure and Hardness of Al-Zn-Mg-Cu Alloy Prepared under Supergravity

Effect of Zr on microstructure evolution of Ti-Mo composite microalloyed steel during rolling

Effect of Zr on static recrystallization of deformed austenite and strain-induced precipitation in Ti microalloyed steel

Effect of cold rolling on microstructure and mechanical properties of pure Zr

Effect of zirconium on inclusions and mechanical properties of China low activation martensitic steel

Influence of Zr on grain orientation, texture, and mechanical properties in hot- and warm-rolled FeCrAl alloys

Effect of Zr Treatment on Inclusion and Solidification Microstructure in Ti Deoxidized Low Carbon Microalloyed Steel

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Microstructure evolution behavior and mechanical mechanisms in a near α-Zr alloy by cold rolling

Effects of Cr and Zr additions on the microstructure and properties of Cu-6wt.% Ag alloys

Enhanced mechanical properties of a Fe-Mn-Al-C austenitic low-density steel by increasing hot-rolling reduction

Influence of Zr content on microstructure and mechanical properties of As-cast Al-Zn-Mg-Cu alloy

The effects of Zr content and hot rolling on the microstructure and mechanical properties of Zn-1.5Cu-1.0Ag-xZr alloys

Effect of zirconium addition on the austenite grain coarsening behavior and mechanical properties of 900 MPa low carbon bainite steel

Effect of Zr Microalloying on the Microstructures and Strengthening Mechanism of As-Cast Al-Fe-Zr Alloys

Superior mechanical properties of pure Zr with heterogeneous structure