Abstract:Accurately evaluating the simple shear in sheet metals has proven to be challenging owing to three reasons: a) the detailed shear strain evaluation is different from one publication to another; b) the measured strain is strongly dependent on the employed virtual strain gauge size (LVSG) when digital image correlation (DIC) is utilized; and c) the negligence of the strain perturbation phenomenon (Swift effects) will only result in a rough estimation of the strain–stress behavior. Thus, in this study, a finite strain perturbation analysis according to the configuration of experimental tests was constructed to understand the shear strain–stress evolution, and a high-resolution quasi-in-situ strain measurement technology was developed to capture the localized shear strain with reliable results. Material anisotropy and simple shear specimen geometry were identified as the two major contributors to the Swift effects. Hence, a finite strain perturbed shear kinematics was first proposed, revealing that some specific shear strain estimations led to a certain degree of error (∼12–25%) at large deformation levels. This work demonstrated that the finite element simulation of simple shear tests, performed using the carefully calibrated YLD2004 yield model, can be utilized to reasonably predict perturbation. A Vickers-indentation-based quasi-in-situ strain measurement was further developed to obtain reliable local strain of the shear zone with LVSG =28 μm. The technique was found to provide high-resolution strain detection to satisfy the necessary conditions of accurate strain measurement when a narrow shear band is present. The results yielded a 30% higher von Mises strain under simple shear deformation than that reported in previous publications for a similar DP980 sheet. The said result was also found to be larger than the fracture strain determined through the so-called “hybrid method”. The proposed perturbed shear kinematics was further implemented in the anisotropic elastoplasticity framework to show that the magnitude of normal stresses did not always remain in the second order with respect to the shear stress due to strain perturbation. Thus, the concept of “perturbed” shear stress was designed to consider the effects of perturbation, and the findings signified a 6–13% change in shear stress compared with the commonly used shear stress for tested scenarios.

Shear characteristics and failure mechanism of laser metal deposition GH4169 at different strain rates

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

Failure Behavior of Laser Metal Deposited Additive Manufacturing Ti-6Al-4V: Effects of Stress State and Initial Defects

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

Influence of Process Parameters on the Interlaminar Shear Strength of CF/PEEK Composites In-Situ Consolidated by Laser-Assisted Automated Fiber Placement

Anisotropic dynamic compression response of an ultra-high strength steel fabricated by laser hybrid additive manufacturing

Thermal deformation behavior and microstructure evolution of GH4169 superalloy under the shear-compression deformation conditions

Dynamic compressive properties and underlying failure mechanisms of selective laser melted Ti-6Al-4V alloy under high temperature and strain rate conditions

Effect of distribution status of the spot matrix on tensile behavior for 42CrMoV when conducting discrete laser surface strengthening: Based on experiment and simulation

Mechanical properties and microstructure evolution of additive manufactured 316L stainless steel under dynamic loading

Effect of laser direct metal deposition process on the microstructure and mechanical properties and temperature and stress fields of 24CrNiMo

Dynamic shear behavior of forged CrMnFeCoNi high entropy alloy using hat-shaped specimens over a wide range of temperatures and strain rates

The microstructural evolution and mechanical response of laser direct energy deposition Inconel 718 alloy based on simulation and experimental methods

Study on the Tensile and Shear Behaviors of Selective Laser Melting Manufactured Ti6Al4V

Investigating the microstructural evolution during deformation of laser additive manufactured Ti–6Al–4V at 400 °C using in-situ EBSD

Influence of Heat-Treatment on the Dynamic Behavior of 3D Laser-Deposited Ti–6Al–4V Alloy

Influence of pulsed laser scanning patterns on microstructural evolution and mechanical properties of Inconel 718 in direct laser deposition

Distribution of Microstructure, Elastic Modulus and Residual Stress Near the Interface in Laser Repaired GH4169 Superalloy

Mechanical Performance of Laser Deposition Repairing of in 738 on Directionally Solidified Superalloy Blade

Simple shear deformation of sheet metals: finite strain perturbation analysis and high-resolution quasi-in-situ strain measurement

Dynamic mechanical response and microstructural evolution of extruded Mg AZ31B plate over a wide range of strain rates