Abstract:The micro-mechanical behavior of lamellar structured Ti6Al4V alloy was studied upon a small strain of 4.5 % compressional loading. The strain and stress concentration is found highly related to individual crystallographic orientation, their size, shape and grain-grain interaction, which usually concentrated along grain boundaries (GBs) typically soft and hard GBs owing to the strong strain gradient incurred. The generated local plastic deformation forms ledges through dislocation accumulation which further activate large amount of Geometrically necessary dislocations (GNDs) to accomodate strain incompatibility. Both strain and stress is maximized at some triple points (TPs). EBSD and crystal plasticity (CP) simulation disclosed some long range meso-bands (about 45° to loading direction) across multi-grains and mini-bands within grain interiors (GIs) with concentrated strain behavior which demonstrate slip and ductile behavior of the Ti6Al4V material. Prismatic slip is found dominated the slip behavior of the Ti6AL4V alloy (mostly from surface dislocation activation) which is away from some findings of literature and largely determined by its low critical resolved shear stress (CRSS). Dislocation is observed emitted from high angle grain boundaries (HAGBs) while slip transmission is observed through both low (LAGBs) and HAGBs. The substructures (α-lamellae), a type of LAGBs allocated within α-colonies, have no significant effect to dislocation movement. Fatigue failure can be inferred from the early stage of micro-mechanical behavior mainly judged by the amount of accumulated plastic deformation and induced stress/strain distribution amont the surroundings. Crack may nucleate from easy prismatic slip, local strain accumulation induced by soft and hard grain clustering (either hard embedded in soft or vice versa usually start from some TPs and sharp corners), or some concentrated long range slip activities. Other than the surface dents induced failure, shearing, cleavage, multi-cleavage and intergranular patterns is presumed highly related to the local microstructure, including their relative size, shape, orientation and grain-grain interactions. The multiple crack origins deemed for reduce fatigue life of shot peened samples regardless of the surface compressional residual stress being generated. The work helps understand the micro-mechanical deformation behavior (down to dislocation level) of Ti6Al4V alloy. Their fatigue and fracture can be inferred from such early stage of strain/stress behavior considering microstructural heterogeneities for similar alloys.

Dynamic compressive properties and underlying failure mechanisms of selective laser melted Ti-6Al-4V alloy under high temperature and strain rate conditions

High strain rate mechanical behavior of Ti-6Al-4V with micro–macro correlation under compressive loading

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

Dynamic Deformation Behavior of the Electron Beam Melted Ti-6Al-4V Alloy

Tensile Behavior of Ti-6Al-4V Alloy Fabricated by Selective Laser Melting: Effects of Microstructures and As-Built Surface Quality

Microstructure, Mechanical Properties, and Constitutive Models for Ti–6Al–4V Alloy Fabricated by Selective Laser Melting (SLM)

Study on the Tensile and Shear Behaviors of Selective Laser Melting Manufactured Ti6Al4V

Influence of Heat-Treatment on the Dynamic Behavior of 3D Laser-Deposited Ti–6Al–4V Alloy

Effect of build orientation on dynamic compressive behaviour of Ti-6Al-4V alloy fabricated by selective laser melting

An investigation of ductile fracture behavior of Ti6Al4V alloy fabricated by selective laser melting

Temperature-Dependent Tension Plastic Deformation and Fracture Behavior of Ti-6.6Al-3.3Mo-1.8Zr-0.29Si Alloy at High Strain Rates

Research on the Dynamic Compressive Deformation Behavior of 3D-Printed Ti6Al4V

Dynamic Strain-Rate Effect On Uniaxial Tension Deformation Of Ti5al2.5sn Alpha-Titanium Alloy At Various Temperatures

Dynamic Response of Ti-6Al-2Zr-1Mo-1V Alloy Manufactured by Laser Powder-Bed Fusion

The Constitutive Responses of Ti-6.6Al-3.3Mo-1.8Zr-0.29Si Alloy at High Strain Rates and Elevated Temperatures

Effect of heating treatment on the microstructural evolution and dynamic tensile properties of Ti-6Al-4V alloy produced by selective laser melting

Comparing the Cold, Warm, and Hot Deformation Flow Behavior of Selective Laser‐Melted and Electron‐Beam‐Melted Ti–6Al–2Sn–4Zr–2Mo Alloy

Micro-mechanical behavior of lamellar structured Ti6Al4V alloy upon compression via experimental and crystal plasticity study

In-situ Comparison of Deformation Behavior at 23 ℃ and 650 ℃ of Laser Direct Melting Deposited Ti-6Al-4V Alloy

Effects of size, geometry, and testing temperature on additively manufactured Ti-6Al-4V titanium alloy

Microstructure and Mechanical Property of Ti–5Al–5Mo–5V–3Cr–1Zr Alloy Fabricated by Selective Laser Melting with a Preheated Substrate