Abstract:Organic light-emitting diode (OLED) has attracted considerable attention due to their unique image quality and market potentials in display field. Efficient blue, green and red emitters with excellent color purity are required for full-color display application, so far great improvements have been achieved for the life time and efficiency of the red and green materials. However, the blue emitting material is still a barrier to commercial applications of OLEDs.Using vacuum thermal evaporation method, blue OLEDs were fabricated by inserting a bathocuproine (BCP) as hole blocking layer (HBL) into conventional double layer (DL) device at the interface of N,N′-bis-(1-naphthyl)-N,N′-biphenyl-1,1′-biphenyl-4,4′-diamine (NPB)/8-hydroxyquinoline aluminum (Alq3). Device structure is indium tin oxide (ITO)/NPB/BCP/Alq/Mg∶Ag, where NPB acts as both hole transporting layer (HTL) and emitting layer (EML), and Alq3 as electron transport layer (ETL). The active emissive area of each device defined by the overlap of ITO and Mg∶Ag was 4 mm×4 mm. Measurements of luminance-voltage (L-V) and current density-voltage (J-V) characteristics were carried out with a Keithley 4200 Semiconductor Characterization System, photoluminescence (PL) and electroluminescence (EL) spectra were measured with an OPT-2000 system. The luminance-voltage and current density-voltage characteristics of devices were investigated, and dif-ferences between their performances were discussed. The results demonstrate that the maximum luminance and luminance efficiency of the BCP device are 2 900 cd/m2 and 0.55 lm/W, respectively. The peak of electroluminescence (EL) spectrum locates at 445 nm and the Commissions Internationale d′Eclairage (CIE) coordinates are (x=0.16, y=0.09), which are independent on the variation of bias voltage. Energy level diagrams were employed to analyze the diversity of device performance with different structures. We find that the high EL performance of the BCP device is attributed to better balance of carriers in the NPB layer by inserting BCP as hole blocking layer (HBL). Optimization of device structure and performance, via adjusting thickness of organic layers, is under investigation.

Double Heterostructure Blue OLEDs

Structure Optimization of Organic Light-Emitting Devices

Studies on the Performances of Blue Organic Electroluminescent Device with Different Electron Transport Layers

Highly Efficient Blue Fluorescent OLEDs with Doped Double Emitting Layers Based on P-N Heterojunctions

Efficient Blue Organic Light-Emitting Diodes with Simple Structure Based on N, N '-Bis (1-Naphthyl)-n, N '-Biphenyl-1, 1 '-Biphenyl-4,4 '-Diamine

Increasing the Efficiency of the Blue OLED Device with a Double-Emitting Layer Structure

P-113: Novel Structure Organic Light-Emitting Diodes with High Performance

Peformance Enhancement Of Organic Light-Emitting Diodes Based On Different Hole Transport Layers

P-113: Society for Information Display: Novel Structure Organic Light-emitting Diodes With High Performance

An Efficient Blue Organic Light Emitting Structure

Improved Performance of Alq(3)-based Organic Light-Emitting Diode with Multi-Layer Structure

Fabrication and Characterization of Blue Organic Light-emitting Diodes Based on N,N′-bis-(1-naphthyl)-N,N′-biphenyl-1,1′-biphenyl-4,4′-diamine

Influence of various doping ratio on optical and electronic performance of blue organic light-emitting diodes

Luminescent Enhancement of Heterostructure Organic Light-Emitting Devices Based on Aluminum Quinolines

Enhanced Color Purity of Blue OLEDs Based on Well-Design Structure

Realizing Highly Efficient Blue Electrofluorescence by Optimized Hybridized Local and Charge Transfer State and Balanced Carrier Mobilities

Highly Efficient Organic Blue Electroluminescent Materials and Devices with Mesoscopic Structures

Preparation and Optoelectronic Performance of Red OLED with Multilayer Structure

Mesoscopic Optical Structure to Enhance the Out-Coupling Efficiency of Blue Top OLED

Optical and electronic performance of multilayer structure green OLED by doping in the Emitter layer

Influence of Different Doping-Sites on the Performance of Double-Layer Heterojuction OLEDs