Abstract:Introduction: Total knee arthroplasty (TKA) is a complex surgical procedure that traditionally relies on two-dimensional radiographs for pre-operative planning. These radiographs may not capture the intricate details of individual knee anatomy, potentially limiting the precision of surgical interventions. With advancements in imaging technology, there is an opportunity to refine TKA outcomes. This study introduces the Native Alignment Phenotype classification system that is based on pre-operative 3-dimensional computed tomography (CT) scans, aiming to provide a more detailed understanding of knee deformities and their influence on characterizing knee osteoarthritis and planning for TKA procedures. Methods: There were 1406 pre-operative non-weight-bearing CT scans analyzed by a single surgeon experienced with robotically-assisted total knee arthroplasties. These scans were converted into three-dimensional models, focusing on the coronal and sagittal planes. Intraoperatively, the robotic system was used to capture native coronal and sagittal deformities for each patient. These values were captured with the patient's leg held in a non-stress, extension pose. A new classification system, 'The Native Alignment Phenotype', was developed to categorize the specific differences between individual knees. Results: There were four primary knee malalignments identified: varus deformity; valgus deformity; and two deformities in the sagittal plane. These malalignments were further categorized based on the degrees of deviation, creating groups with 5° coronal and sagittal ranges. A total of 77 phenotypic alignment patterns were found based on the analyzed cohort. In the coronal plane, varus HKA deformity between 6 and 10° was the most common, with 36.9% of the cases, followed by varus HKA alignment, which was between 0 and 5°, representing 34.3% of the cases. In the sagittal plane, neutral and flexion contracture deformities between 0 and 5° were the most common, with 32.6% of the cases, followed by a fixed flexion contracture alignment, which was between 6 and 10°, representing 28.7% of the cases. When combining coronal and sagittal planes, the most common alignment was the varus between 0 and 5° with a flexion contracture between 0 and 5° (12.5% of cases), closely followed by the varus between 6 and 10° with a flexion contracture between 6 and 10° (12.4% of cases). Conclusion: The Native Alignment Phenotype classification system offers a nuanced understanding of knee deformities based on three-dimensional (CT scan) assessments, potentially leading to improved surgical outcomes in TKA. By leveraging the detailed data from the CT scans, this system provides a more comprehensive view of the knee's anatomy, emphasizing the importance of individualized, data-driven approaches in knee surgery.

Prosthetic matching of knee valgus for total knee arthroplasty: three-dimensional digital measurement and analysis

Measurement of femoral posterior condylar offset and posterior tibial slope in normal knees based on 3D reconstruction

Bony Landmarks and Rotational Alignment in Total Knee Arthroplasty for Chinese Osteoarthritic Knees with Varus or Valgus Deformities

[Rotational Landmarks and Total Knee Arthroplasty in Osteoarthritic Knees].

Total Knee Arthroplasty in Ranawat II Valgus Deformity with Enlarged Femoral Valgus Cut Angle: A New Technique to Achieve Balanced Gap.

Quantitative Analysis of Rotational Alignment after Total Knee Arthroplasty in Osteoarthritis

[Evaluation and Analysis of the Tibial Coronal Alignment after Total Knee Replacement with the Extramedullary Tibial Cutting Guided by the Tibial Tubercle and Anterior Tibial Tendon in Chinese Patients].

Comparative study of CT measurement and physical measurement of femoral posterior condylar angle

How to make a psychiatric diagnosis.

Comprehensive Assessment of Patellar Morphology Using Computed Tomography-Based Three-Dimensional Computer Models.

[Comparison of Alignment and Position of Prosthesis Between Portable Accelerometer-Based Navigation Device and Conventional Instrumentation in Total Knee Arthroplasty with Valgus Deformity].

Influence of femoral intramedullary guides on the limb alignment in total knee arthroplasty

A Kinematic Study of the Tibiofemoral Joint after Total Knee Arthroplasty Using in Vivo Fluoroscopy and Digital Model

Three-dimensional-based native alignment phenotype classification system: Description for use in planning for deformities during total knee arthroplasty

Morphometric Assessment and Virtual Resection of the Patellae on Three Dimensional CT-based Models Using Computer Assisted Technology

The measurement and clinical significance of tibial torsion abnormality for knee osteoarthritis

An MRI-Based Correlation Study Investigating the Effect of Varying Posterior Femoral Condyle Angles on the Patellofemoral Joint

Three-dimensional gait characteristics of patients after unilateral total knee arthroplasty

Reliable prediction of implant size and axial alignment in AI-based 3D preoperative planning for total knee arthroplasty

Measurement of Posterior Slope of the Medial Tibial Plateau in Chinese

Guidelines for Instrumentation for Total Knee Replacement Based on Frontal Plane Radiographs.