Abstract:Objective This study investigated the stress distribution in a femur after a cemented prosthetic replacement surgery in elderly patients with a partial marrow type I intertrochanteric fracture and compared the differences in stress distribution between a long- and short-stem prosthetic replacement. Methods A spiral computed tomography (CT) scan was used on the volunteer’s right femur to obtain image data, which were processed with the Mimics software and the modeling software to reconstruct a three-dimensional model of the femur. On this basis, the three-dimensional physical models for a partial marrow type intertrochanteric fracture, long- and short-stem femoral prostheses, and the mantle layer of cement were established. Finally, the three-dimensional finite element models of the long- and short-stem femoral prostheses as a treatment of an intertrochanteric fracture were established using the software for finite element analysis, and the biomechanical analysis was implemented for the models. Results The stress distribution in the femur after the cemented long- or short-stem prosthetic replacement did not change significantly; it still gradually increased from the proximal end to the distal end, reaching the peak value at the lower 1/3 of the medial and lateral junction, and then decreased to the end. Although a stress concentration zone formed in the medial and lateral end of the bone cement-prosthetic stem interface in the short-stem prosthesis, which had a lateral peak value of 15.3 MPa, it did not exceed the fatigue strength of the bone cement. Alternatively, a stress concentration zone formed in the distal medial and lateral end of the bone cement-prosthetic stem interface and the medial middle part of the shaft in the long-stem prosthesis, which showed a peak value that was also lower than the fatigue strength of the bone cement. No significant stress concentration zones were found in the femoral calcar reconstructed by bone cement. Conclusion The stress distribution in the femur did not change significantly after cemented long- and short-stem prosthetic replacements were used for elderly patients with a partial marrow type I intertrochanteric fracture. The probability of loosening of the cemented long-stem prosthesis was comparable to that of the short-stem prosthesis, but the latter may be more suitable for treating elderly patients with a partial marrow type I intertrochanteric fracture due to the shorter surgery time, minor trauma, and fewer complications.

Finite element analysis on the femoral revision with two types of revision hip stems

Non-contemporaneous bilateral stem fractures occurring after staged bilateral hip revision using extensively porous-coated cylindrical femoral stems: a case report

Femoral Component Revision Using Extensively Porous-Coated Cementless Stem.

Comparison of femoral mechanics before and after internal fixation removal and the effect of sclerosis on femoral stress: a finite element analysis

Finite Element Analysis of Tibia after Revision of TKA Through Impaction Bone Grafting

Finite Element Analysis of Femoral Stress Changes after Total Hip Arthroplasty

[Analysis on Morphology and Stability of Femoral Hip Prosthesis Based on the Revision Operation].

Comparison of Cylindrical and Tapered Stem Designs for Femoral Revision Hip Arthroplasty

Comparison of Early Postoperative Stress Distribution around Short and Tapered Wedge Stems in Femurs with Different Femoral Marrow Cavity Geometries Using Finite Element Analysis

Finite element analysis of changes in femoral stresses after elite total hip arthroplasty]

Theoretical analysis of changes in femoral stresses after total hip arthroplasty]

The Biomechanical Study of Intertrochanic Fractures Treated with Cemented Femoral Stem

Stress Analysis and Shape Design of a Femoral Hip Prosthesis

The Comparative Analysis with Finite Element for Cemented Long- and Short-Stem Prosthetic Replacement in Elderly Patients with a Partial Marrow Type I Intertrochanteric Fracture

Femoral Bone Remodeling in Revision Total Hip Arthroplasty with Use of Modular Compared with Monoblock Tapered Fluted Titanium Stems: the Role of Stem Length and Stiffness.

A biomechanical comparison of four different cementless press-fit stems used in revision surgery for total knee replacements

The Contour of Cementless Femoral Stem Has Minor Effect on Initial Periprosthetic Von Mises Stress Distribution. A 3-Dimensional Finite Element Analysis.

Effects of different materials on stress distribution and biomechanics of bone interface of artificial hip joint

Effects of Materials of Cementless Femoral Stem on the Functional Adaptation of Bone

Finite Element Analysis of Optimal Design of Distal Geometry of Cementless Femoral Prosthesis

Comparison of two tapered fluted modular titanium (TFMT) stems used in revision hip arthroplasty from a single center