Abstract:Objective This study investigated the stress distribution in a femur after a cemented prosthetic replacement surgery in elderly patients with a partial marrow type I intertrochanteric fracture and compared the differences in stress distribution between a long- and short-stem prosthetic replacement. Methods A spiral computed tomography (CT) scan was used on the volunteer’s right femur to obtain image data, which were processed with the Mimics software and the modeling software to reconstruct a three-dimensional model of the femur. On this basis, the three-dimensional physical models for a partial marrow type intertrochanteric fracture, long- and short-stem femoral prostheses, and the mantle layer of cement were established. Finally, the three-dimensional finite element models of the long- and short-stem femoral prostheses as a treatment of an intertrochanteric fracture were established using the software for finite element analysis, and the biomechanical analysis was implemented for the models. Results The stress distribution in the femur after the cemented long- or short-stem prosthetic replacement did not change significantly; it still gradually increased from the proximal end to the distal end, reaching the peak value at the lower 1/3 of the medial and lateral junction, and then decreased to the end. Although a stress concentration zone formed in the medial and lateral end of the bone cement-prosthetic stem interface in the short-stem prosthesis, which had a lateral peak value of 15.3 MPa, it did not exceed the fatigue strength of the bone cement. Alternatively, a stress concentration zone formed in the distal medial and lateral end of the bone cement-prosthetic stem interface and the medial middle part of the shaft in the long-stem prosthesis, which showed a peak value that was also lower than the fatigue strength of the bone cement. No significant stress concentration zones were found in the femoral calcar reconstructed by bone cement. Conclusion The stress distribution in the femur did not change significantly after cemented long- and short-stem prosthetic replacements were used for elderly patients with a partial marrow type I intertrochanteric fracture. The probability of loosening of the cemented long-stem prosthesis was comparable to that of the short-stem prosthesis, but the latter may be more suitable for treating elderly patients with a partial marrow type I intertrochanteric fracture due to the shorter surgery time, minor trauma, and fewer complications.

Finite Element Analysis of Tibia after Revision of TKA Through Impaction Bone Grafting

Non-contemporaneous bilateral stem fractures occurring after staged bilateral hip revision using extensively porous-coated cylindrical femoral stems: a case report

Finite Element Analysis of Femoral Stress Changes after Total Hip Arthroplasty

Mechanical Test of Impaction Bone Grafting in Revision of Tibia (Initial Stability of Short and Long Stem)

Theoretical analysis of changes in femoral stresses after total hip arthroplasty]

Finite Element Analysis of Total Knee Replacement with Various Misalignment Angles in the Sagittal Plane

Finite element analysis of changes in femoral stresses after elite total hip arthroplasty]

Finite-element analysis of the influence of tibial implant fixation design of total ankle replacement on bone-implant interfacial biomechanical performance

Finite element analysis on the femoral revision with two types of revision hip stems

Femur Biomechanical Changes Caused by Femoral Stem Extension Implant in Total Knee Arthroplasty

The Biomechanical Study of Intertrochanic Fractures Treated with Cemented Femoral Stem

The Comparative Analysis with Finite Element for Cemented Long- and Short-Stem Prosthetic Replacement in Elderly Patients with a Partial Marrow Type I Intertrochanteric Fracture

Biomechanical evaluation of total ankle arthroplasty. Part II: Influence of loading and fixation design on tibial bone-implant interaction

[Analysis on Morphology and Stability of Femoral Hip Prosthesis Based on the Revision Operation].

Finite element stress analysis of the bearing component and bone resected surfaces for total ankle replacement with different implant material combinations

A Biomechanical Comparison of Two Intramedullary Implants for Subtrochanteric Fracture in Two Healing Stages: A Finite Element Analysis

Finite Element Analysis of A Retrieved Custom-Made Knee Prosthesis

Comparison of Early Postoperative Stress Distribution around Short and Tapered Wedge Stems in Femurs with Different Femoral Marrow Cavity Geometries Using Finite Element Analysis

Finite Element Analysis of Fixed-Bearing Knee Prosthesis with Different Size of Femur and Tibia Parts

Comparative analysis of the biomechanical behavior of two different design metaphyseal-fitting short stems using digital image correlation

Influences of Different Implant Material Combinations on the Stress Distribution of the Foot Following Total Ankle Replacement: a Finite Element Analysis