Abstract:Abstract Background The progressive evolution in hip replacement research is directed to follow the principles of bone and soft tissue sparing surgery. Regarding hip implants, a renewed interest has been raised towards short uncemented femoral implants. A heterogeneous group of short stems have been designed with the aim to approximate initial, post-implantation bone strain to the preoperative levels in order to minimize the effects of stress shielding. This study aims to investigate the biomechanical properties of two distinctly designed femoral implants, the TRI-LOCK Bone Preservation Stem, a shortened conventional stem and the Minima S Femoral Stem, an even shorter and anatomically shaped stem, based on experiments and numerical simulations. Furthermore, finite element models of implant–bone constructs should be evaluated for their validity against mechanical tests wherever it is possible. In this work, the validation was performed via a direct comparison of the FE calculated strain fields with their experimental equivalents obtained using the digital image correlation technique. Results Design differences between Trilock BPS and Minima S femoral stems conditioned different strain pattern distributions. A distally shifting load distribution pattern as a result of implant insertion and also an obvious decrease of strain in the medial proximal aspect of the femur was noted for both stems. Strain changes induced after the implantation of the Trilock BPS stem at the lateral surface were greater compared to the non-implanted femur response, as opposed to those exhibited by the Minima S stem. Linear correlation analyses revealed a reasonable agreement between the numerical and experimental data in the majority of cases. Conclusion The study findings support the use of DIC technique as a preclinical evaluation tool of the biomechanical behavior induced by different implants and also identify its potential for experimental FE model validation. Furthermore, a proximal stress-shielding effect was noted after the implantation of both short-stem designs. Design-specific variations in short stems were sufficient to produce dissimilar biomechanical behaviors, although their clinical implication must be investigated through comparative clinical studies.

Mechanical Test of Impaction Bone Grafting in Revision of Tibia (Initial Stability of Short and Long Stem)

Mechanical Properties Of 7-10 Mm Bone Grafts And Small Slurry Grafts In Impaction Bone Grafting

Finite Element Analysis of Tibia after Revision of TKA Through Impaction Bone Grafting

The Biomechanical Study of Intertrochanic Fractures Treated with Cemented Femoral Stem

Assessment of the primary stability of revision tibial trays augmented with a cementless sleeve in AORI Type III defects

The influence of stem length and fixation on initial femoral component stability in revision total knee replacement

Biomechanical Research on Contour Cage with Transacetabular Screws Fixation in Revision Total Hip Arthroplasty.

Biomechanical comparison between metal block and cement-screw techniques for the treatment of tibial bone defects in total knee arthroplasty based on finite element analysis

Stability of Three‐Dimensional Printed Custom‐Made Metaphyseal Cone for Tibial Bone Defects Reconstruction: A Finite Element Analysis and Biomechanical Study

Progress on the investigation of BMP application in revision total hip arthroplasty

Comparative analysis of the biomechanical behavior of two different design metaphyseal-fitting short stems using digital image correlation

Primary stability of tibial plateaus under dynamic compression-shear loading in human tibiae - Influence of keel length, cementation area and tibial stem

Finite-element analysis of the influence of tibial implant fixation design of total ankle replacement on bone-implant interfacial biomechanical performance

Comparison of Early Postoperative Stress Distribution around Short and Tapered Wedge Stems in Femurs with Different Femoral Marrow Cavity Geometries Using Finite Element Analysis

Short-term comparison of survivorship and functional outcomes for metaphyseal cones with short and long stems in revision total knee arthroplasty

Biomechanical evaluation of total ankle arthroplasty. Part II: Influence of loading and fixation design on tibial bone-implant interaction

Biomechanical Experiment of Non-stemmed Anatomical Total Hip Prosthesis Arthroplasty in Vitro

Diaphyseal Impaction Grafting Combined with Metaphyseal Cones: Outcomes in 88 Revision Total Knee Arthroplasties

The Stability of Fixation of Vancouver B2 Periprosthetic Femoral Fractures: Effect of Implantation Technique

Application of uncemented distal fixation femoral stem combined with allograft in femoral revision with proximal bone defect

Effect of bone density and cement morphology on biomechanical stability of tibial unicompartmental knee arthroplasty