Abstract:Statement of problem: Adaptation between abutment and suprastructure plays a crucial role in the long-term success of implant-supported metal-ceramic crowns. Fabrication methods, the porcelain firing stage, and cementation techniques may affect the marginal adaptation between the crown and abutment. However, the information regarding this issue is sparse. Purpose: The purpose of this in vitro study was to compare marginal fit after the fabrication of cobalt-chromium alloy copings, porcelain firing, and cementation of metal-ceramic restorations that were fabricated with computer-aided design and computer-aided manufacturing (CAD-CAM) milling and direct metal laser sintering techniques. Material and methods: Thirty straight tissue-level titanium abutments were screwed onto implant analogs. All specimens were embedded in acrylic resin and divided into 2 groups according to CAD-CAM milling and direct metal laser sintering fabrication of the metal coping. Fifteen cobalt-chromium implant-supported metal copings were fabricated by using the CAD-CAM milling technique and 15 by using the direct metal laser sintering technique. In both groups, marginal gap measurements between the cobalt-chromium copings and abutments were obtained before (T0) and after the placement of the ceramic veneer (T1) and after cementation (T2) by using a stereomicroscope with a magnification of ×40. The data were statistically evaluated by using 2-way ANOVA and the Tukey post hoc test (α=.05). A t test was used to determine whether there were significant differences between the fabrication techniques (α=.05). Results: A significant difference in the fabrication stages was found in the direct metal laser sintering group. The direct metal laser sintering coping group and porcelain applied direct metal laser sintering group had a statistically lower marginal gap value than the cemented direct metal laser sintering group (P=.021, P=.038). The direct metal laser sintering coping group had a lower marginal gap value than the CAD-CAM milling coping group, although the difference was not statistically significant (P=.216). Conclusions: Porcelain firing and cementation increased the marginal gap between the crown and abutment. No statistically significant differences were found between the direct metal laser sintering and CAD-CAM milling techniques in terms of marginal fit.

Effect of different convergence angles on the fitness of using selective laser melting technique to fix crowns

Effect of Machining Method and Margin Design on the Accuracy and Margin Quality of Monolithic Zirconia Crowns

[Comparative Adaptation of Crowns of Selective Laser Melting and Wax-Lost-casting Method].

Dimensional accuracy and internal and marginal fit evaluation of Co-Cr crowns prepared by SLM

Marginal Misfit of 3D-Printed (Selective Laser Sintered), CAD-CAM and Lost Wax Technique Cobalt Chromium Copings with Shoulder and Chamfer Finish Lines: An In-Vitro Study

Looking at the aquatic contamination through fish eyes--a faithful picture based on metals burden.

Three-Dimensional Analysis of Internal Adaptations of Crowns Cast from Resin Patterns Fabricated Using Computer-Aided Design/Computer- Assisted Manufacturing Technologies

Comparison of marginal fit of gold electroforming-ceramic crown,high gold alloy-ceramic crown and nickel chromium alloy-ceramic crown

Therapy and clinical trials.

Well-Differentiated Duodenal Tumor/Carcinoma (Excluding Gastrinomas)

Comparison of the internal fit of metal crowns fabricated by traditional casting, computer numerical control milling, and three-dimensional printing

Care coordination metrics in a health information exchange enabled environment

Performance of Stereolithography and Milling in Fabricating Monolithic Zirconia Crowns with Different Finish Line Designs.

Marginal and internal fit of metal-ceramic crowns fabricated with a new laser melting technology

The Impact of Open versus Closed Computer-Aided Design/Computer-Aided Manufacturing Systems on the Marginal Gap of Zirconia-Reinforced Lithium Silicate Single Crowns Evaluated by Scanning Electron Microscopy: A Comparative In Vitro Study

Influence of various fabrication techniques and porcelain firing on the accuracy of metal-ceramic crowns

Effect of cavity depths on the marginal and internal discrepancy of endocrowns in vitro

Effect of porcelain firing and cementation on the marginal fit of implant-supported metal-ceramic restorations fabricated by additive or subtractive manufacturing methods

Effect of abutment finish lines on the mechanical behavior and marginal fit of screw-retained implant crowns: An in vitro study

Digital Evaluation of Absolute Marginal Discrepancy: A Comparison of Ceramic Crowns Fabricated with Conventional and Digital Techniques

The Influence of Extra-Fine Milling Protocol on the Internal Fit of CAD/CAM Composite and Ceramic Crowns