Abstract:Introduction: During warm vertical compaction of gutta-percha, root canal sealers with different chemical compositions absorb the heat generated inside the root canal. The aim of this research was to assess physicochemical modifications of sealers subjected to the System B heat source (Analytic Technology, Redmond, WA) and to evaluate the effect that the use of different sealers has on the heat transfer to the external root surface. Methods: Three proprietary brand sealers (AH Plus [Dentsply International, Addlestone, UK], Pulp Canal Sealer [Kerr Corporation, Orange, CA], MTA Fillapex [Angelus Dental Solutions, Londrina, PR, Brazil]) and a prototype sealer based on Portland cement were assessed. The heat generated on the surfaces of System pluggers and the heat dissipation at different levels (apical, midroot, and cervical) over root surface while using different sealers was assessed using thermocouples. Data were collected in 3 different environmental conditions with the tooth suspended in air, immersed in Hank's balanced salt solution, or gelatinized Hank's balanced salt solution. Chemical changes in the sealers induced by the heat were monitored by Fourier transform infrared spectroscopy. The effect of heat changes on the setting time and compressive strength of the sealers was also assessed. Results: The continuous wave plugger sustained a rise in temperature at a maximum of 80°C at the instrument shank. The highest change in temperature on the external root surface was recorded after 1.5 minutes from the start of heating, and it was restored to body temperature by 6 minutes. Environmental conditions affected heat dissipation for all the sealers in the midroot and cervical regions and the highest increase in temperature (∼60°C) recorded in air. In the midroot and cervical regions, the type of sealer used did not affect the rise in temperature. In the apical region, AH Plus obturations resulted in a greater rise in temperature, and the chemical composition of this sealer was affected by high temperature; it also induced a reduction in sealer setting time and strength. Conclusions: It could be concluded that surrounding conditions, such as temperature and humidity, exerted influence on heating dissipation during the continuous wave of the condensation obturation technique and that root canal sealers presented different conductive/isolating properties. Furthermore, the physical and chemical properties of AH Plus were negatively affected by the changes in temperature.

Assessment of Root Surface Temperature Changes Generated by the ObturaII System in Vitro.

In Vitro Root Surface Temperature Rises During Root Canal Obturation by BeeFill~(TM) 2in1 Technique

Assessment of the root surface temperature during the use of intracanal agitation systems: In vitro study

Outcome of Root Canal Treatment Using Warm Vertical Compaction with Bioceramic and Resin-Based Sealers: A Randomised Clinical Trial.

Temperature changes of tooth surfaces under ultrasonic tip working against the wall of root canals-an in vitro study

ROOT SURFACE TEMPERATURE MEASUREMENT DURING ROOT CANAL OBTURATION

In vitro evaluation of temperature change on the root surface after the removal of root canal filling

Temperature Field in Bone During Robotic Dental Implant Drilling: Theoretical Models and in Vitro Experiments

In Vitro Investigation of Heat Transfer in Human Tooth

In vitro Study of Temperature Changes on the Outer Root Surface of Extracted Human Teeth Under Different Parameters of Intracanal Cryotherapy

Comparative evaluation of increase in temperature on the external root surface of teeth during retrieval of broken NiTi instrument using two ultrasonic tips and two power settings: An in vitro study

[Temperature Variation at the External Root Surface During Nd: YAG Laser Irradiation in the Root Canal in Vitro].

Intraosseous Temperature Changes During Implant Site Preparation: In Vitro Comparison of Thermocouples and Infrared Thermography

Investigation of the effect of sealer use on the heat generated at the external root surface during root canal obturation using warm vertical compaction technique with System B heat source

Thermal transfer in extracted incisors during thermal pulp sensitivity testing

XP‐Endo Finisher behaviour and irrigant temperature in intracanal environment: Clinical measurements

The accuracy of using guided endodontics in access cavity preparation and the temperature changes of root surface: An in vitro study

Effect of composite temperature on in vitro intrapulpal temperature rise

Pulpal Temperature Variances During Step-by-step Adhesive Restorative Procedure Using Three Different High-irradiance Light-curing Units

Evaluation of temperature increase during in-office bleaching

Temperature Variation in the Pulp During Nd-YAG Laser Irradiation at Tooth Cervical Protion in Vitro