Abstract:Objectives: Evaluate the effect of environment on post-gel shrinkage (Shr), cuspal strains (CS), microtensile bond strength (μTBS), elastic modulus (E) and shrinkage stress in molars with large class II restorations. Methods: Sixty human molars received standardized Class II mesio-oclusal-distal cavity preparations. Restorations were made with two composites (CHA, Charisma Diamond, Heraus Kulzer and IPS Empress Direct, Ivoclar-Vivadent) using three environment conditions (22°C/50% humidity, 37°C/50% humidity and 37°C/90% humidity) simulated in custom developed chamber. Shr was measured using the strain gauge technique (n=10). CS was measured using strain gauges. Half of the teeth (n=5) were used to assess the elastic modulus (E) and Knoop hardness (KHN) at different depths using microhardness indentation. The other half (n=5) was used to measure the μTBS. The composites and environment conditions were simulated in a two-dimensional finite element analysis of a tooth restoration. Polymerization shrinkage was modeled using Shr data. The Shr, CS, μTBS, KHN and E data were statistically analyzed using two-way ANOVA and Tukey test (significance level: 0.05). Results: Both composites had similar Shr, CS, μTBS and shrinkage stress. CHA had higher elastic modulus than IPS. Increasing temperature and humidity significantly increased Shr, CS and shrinkage stress. μTBS were similar for groups with lower humidity, irrespective of temperature, and higher with higher humidity. E and KHN were constant through the depth for CHA. E and KHN values were affected by environment only for IPS, mainly deeper in the cavity. Shrinkage stress at dentin/composite interface had high inverse correlation with μTBS. Shrinkage stress in enamel had high correlation with CS. Conclusions: Increasing temperature and humidity caused higher post-gel shrinkage and cusp deformation with higher shrinkage stresses in the tooth structure and tooth/restoration interface for both composites tested. The chamber developed for simulating the oral environment conditions will improve the realism of in vitro studies. Clinical significance Simulating oral temperature and humidity is important to better determine the biomechanical behavior of composite resin restoration. Avoiding high humidity during restorative procedures using rubber dam isolation may reduce cuspal deformation and shrinkage stress and improve the bonding strength of posterior composite restorations.

Effect of composite temperature on in vitro intrapulpal temperature rise

Evaluation of pulp chamber temperature during cementation with the preheated composite resin technique

Influence of light exposure techniques on in vitro pulp temperature rise during bulk fill composite Class I restorations

Temperature change of the pulpal floor and restoration with preheated bis-GMA free and containing resin composite (a randomized clinical trial)

Composite Cure and Pulp-Cell Cytotoxicity Associated with LED Curing Lights.

Pulpal Temperature Variances During Step-by-step Adhesive Restorative Procedure Using Three Different High-irradiance Light-curing Units

Durability of Four Composite Resin Cements Bonded to Dentin under Simulated Pulpal Pressure

Temperature change in pulp chamber of primary teeth during curing of coloured compomers: an in vitro study using pulpal blood microcirculation model

Evaluation of temperature increase during in-office bleaching

The role of protective liners and glass ionomer in managing pulp temperature during light curing

Effect of Rapid High-Intensity Light-Curing on Increasing Transdentinal Temperature and Cell Viability: An In Vitro Study

The effect of preheating on light cured resin composites

Heat generated during dental treatments affecting intrapulpal temperature: a review

The Effect of Light-emitting Diode Light Intensities and Duration of Cure on Pulpal Wall Temperature among Different Classes of Teeth

Effect of translucency and absorbance of composite on temperature change during photopolymerization

[Influence of Intra-Pulpal Temperature when Using Femtosecond Laser in Specific Parameters to Prepare Cavities in Tooth Enamel: an in Vitro Study].

Assessment of the root surface temperature during the use of intracanal agitation systems: In vitro study

Composite Resin Preheating Techniques for Cementation of Indirect Restorations

Thermal transfer in extracted incisors during thermal pulp sensitivity testing

Effect of temperature and humidity on post-gel shrinkage, cusp deformation, bond strength and shrinkage stress - Construction of a chamber to simulate the oral environment

The Effect of Water Coolant and Bur Type on Pulp Temperature When Removing Tooth Structure and Restorative Dental Materials