Abstract:Context: An unfavorable event that can hinder endodontic treatment and affect the outcome of root canal treatment is the separation of endodontic instruments. Endodontic instrument separation can occur due to clinical or metallurgical factors. Friction between the ultrasonic tip and the remaining dentin generates heat, which is subsequently transferred to the external root surface. Elevated temperatures exceeding 10°C above body temperature for more than a minute may result in injury to periodontal or bone tissue. Aim: The aim of this study was to evaluate and compare temperature rise on the external root surface of teeth during retrieval of broken NiTi instrument using two different ultrasonic tips and two power settings. Materials and methods: In each group, a sample size of 8 was sufficient to attain a statistical power exceeding 90%, enabling the detection of a minimum mean difference of 0.9204 (delta) through a one-way ANOVA test at a 95% confidence level (alpha 0.05). After access opening and working length determination, samples were randomly distributed into two groups - Group 1 (A and B) - ProUltra tip at high and low power settings and Group 2 (A and B) - Cric Dental IR3 at high and low power settings. The temperature rise was measured using K-type thermocouple thermometer. The comparisons were analyzed using the Kruskal-Wallis test with pairwise comparisons using the Dunn's test. Results: Group 1A and Group 1B resulted in lower heat generation compared to Group 2A and 2B and its difference was statistically significant (P < 0.05). Minimum temperature rise is seen in the ProUltra group at lower power settings (Group 1A) at the apical level and maximum temperature rise is seen in the Cric Dental IR3 group at higher power settings (Group 2B) at the middle third level. Conclusion: It was found that there is a significant temperature rise seen when ultrasonic tips are used for the retrieval of separated files, especially at higher power settings. The ProUltra tip demonstrated the lowest temperature rise at lower power settings, particularly at the apical level, whereas the IR3 Cric Dental tip exhibited the highest temperature rise, notably at higher power settings and the middle third level.

Temperature changes of tooth surfaces under ultrasonic tip working against the wall of root canals-an in vitro study

Comparative evaluation of increase in temperature on the external root surface of teeth during retrieval of broken NiTi instrument using two ultrasonic tips and two power settings: An in vitro study

[Heat propagation in dentin during cavity preparation in vitro with oscillating instruments]

Assessment of the root surface temperature during the use of intracanal agitation systems: In vitro study

The accuracy of using guided endodontics in access cavity preparation and the temperature changes of root surface: An in vitro study

Thermal transfer in extracted incisors during thermal pulp sensitivity testing

Regulation and Measurement of the Heat Generated by Automatic Tooth Preparation in A Confined Space

[Influence of Intra-Pulpal Temperature when Using Femtosecond Laser in Specific Parameters to Prepare Cavities in Tooth Enamel: an in Vitro Study].

Temperature Variation in the Pulp During Nd-YAG Laser Irradiation at Tooth Cervical Protion in Vitro

[Temperature Variation at the External Root Surface During Nd: YAG Laser Irradiation in the Root Canal in Vitro].

Assessment of Root Surface Temperature Changes Generated by the ObturaII System in Vitro.

Heat generated during dental treatments affecting intrapulpal temperature: a review

Intra-pulpal and subsurface temperature rise during tooth irradiation with 808 nm diode laser: an in vitro study

Effect of Ultrasonic Irrigation on Eliminating the Endotoxin in Infected Root Canals

In vitro Study of Temperature Changes on the Outer Root Surface of Extracted Human Teeth Under Different Parameters of Intracanal Cryotherapy

Efficacy Analysis of Ultrasonic Instrument Used in Premolar's Root Canal Therapy

Periodontal Blood Flow Protects the Alveolar Bone from Thermal Injury during Thermoplasticized Obturation: A Finite Element Analysis Study

Effect of inflow temperature on root canal irrigation: A computational fluid dynamics study

In vitro evaluation of temperature change on the root surface after the removal of root canal filling

The role of protective liners and glass ionomer in managing pulp temperature during light curing

Pulpal Temperature Variances During Step-by-step Adhesive Restorative Procedure Using Three Different High-irradiance Light-curing Units