Abstract:Objective To compare the pre-and post-operative tumor target volume and to examine the consistency in physical dosimetric parameters of organs at risk (OAR) following 3D-printed coplanar template (3D-PCT)-assisted and CT-guided radioactive seed implantation.Methods The 3D-printed coplanar template was designed using a computer software, and the coordinate system was established where the center was used as the basis for setting the x axis and y axis.Crosses defining the center of treatment were drawn on the patient''s body and matched with the corresponding central point, x axis, and y axis of the coplanar template.3D-PCT-assisted and CT-guided radioactive seed implantation was performed based on the pre-operative plan, and the pre-operative, operative, and post-operative plans were designed to evaluate the target tumor volume and the normal dose received by the tissues.In addition, dosimetric parameters, including D90(minimum dose received by 90% of the gross target volume), V100, V150, V200(percentage of GTV that received 100%, 150%, and 200% of the prescribed dose, respectively), minimum peripheral dose (MPD), conformal index (CI), external index (EI), and homogeneity index (HI) in the pre-operative and post-operative plans were also assessed and compared using the Wilcoxon test. Results Fourteen patients treated in our institution from August to October, 2016 were included in this study. The median age of the patients was 61.5 years, and the median Karnofsky Performance Scale score was 80. A total of 14 lesions from the 14 patients were treated by seed implantation in the neck (n=4), chest (n=3), abdomen (n=5), and pelvis (n=2). Of the 14 patients that underwent implantation, 8 had previously received radiation therapy, and 6 had not received radiation therapy. Dosage optimization was performed for all patients during the operation. The median activity of the implanted seeds was 0.625 mCi (0.55-0.75 mCi,1 Ci=3.7×1010 Bq), and the preoperatively planned median number of needling and implanted seeds were 9(4-34) and 45.5(10-162), respectively. However, the actual median number of needling and implanted seeds were 9.5(4-34) and 45.5(10-162), respectively. Dosimetric analysis showed that there were no significant changes in tumor volume (P=0.135), D90(P=0.208), MPD (P=0.104), V100(P=0.542), V150(P=0.754), V200(P=0.583), CI (P=0.426), EI (P=0.326), and HI (P=0.952) after implantation. Conclusions 3D-PCT guidance and dosage optimization can result in good consistency between pre-and post-operative plans for radioactive seed implantation. 3D-PCT is a convenient and cheap technique suitable for large-scale clinical application.

3D-PRINTING NON-COPLANAR TEMPLATE ASSISTANT CT - GUIDED 125I SEEDS IMPLANTATION ON PELVIC RECURRENT CERVICAL CANCER

3D Individual Template Combined CT Image Guided Low Dose Rate 125I Seeds Implantation for Pelvic Recurrent Cervical Cancer

Dosimetric Study of 125I Seeds Implantation by 3D-Printing Coplanar Template for Pelvic Wall Recurrent Cervical Cancer after Radiotherapy

[CT Guidance 125I Seed Implantation for Pelvic Recurrent Rectal Cancer Assisted by 3D Printing Individual Non-Coplanar Template].

Dosimetry of CT Guidance I-125 Seed Implantation for Pelvic Recurrent Rectal Cancer Assisted by 3D Printing Individual Noncoplanar Templates

3D-printing non-coplanar template assisted 125I seed implantation for pelvic tumor: individual template design method

Dosimetry Evaluation for CT Guided 125I Seeds Implantation Assisted by Three-Dimensional-printing Coplanar Coordinate Template in Chest Malignant Tumor

Dosimetry Evaluation of Navigation System-Assisted and CT-guided Seed Implantation in the Treatment of Recurrent Malignant Pelvic Tumors

Accuracy and Dosimetric Parameters Comparison of 3D-Printed Non-Coplanar Template-Assisted Computed Tomography-Guided Iodine-125 Seed Ablative Brachytherapy in Pelvic Lateral Recurrence of Gynecological Carcinomas

Computed Tomography Image-Guided and Personalized 3D Printed Template-Assisted 125-Iodine Seed Implantation for Recurrent Pelvic Tumor: a Dosimetric Study

Expert Consensus on Computed Tomography-Assisted Three-Dimensional-printed Coplanar Template Guidance for Interstitial Permanent Radioactive125i Seed Implantation Therapy

The Dosimetry Evaluation of 3D Printing Non-Coplanar Template-Assisted CT-guided 125I Seed Stereotactic Ablation Brachytherapy for Pelvic Recurrent Rectal Cancer after External Beam Radiotherapy.

Dosimetric Analysis of 3D-Printed Coplanar Template-Assisted and CT-guided 125I Seed Implantation for the Treatment of Malignant Tumors

Comparison of Planning Between 3D-Printing Non-Coplanar Template and 3D-Printing Coplanar Template-Assisted Radioactive Seed Implantation As Re-Irradiation for Pelvic Wall Recurrent Gynecological Malignant Tumors

Analysis on the Accuracy of CT-guided Radioactive I-125 Seed Implantation with 3D Printing Template Assistance in the Treatment of Thoracic Malignant Tumors.

3D-Printed Template and Optical Needle Navigation in CT-guided Iodine-125 Permanent Seed Implantation

Dosimetry Verification of 125 I Seeds Implantation With Three-Dimensional Printing Noncoplanar Templates and CT Guidance for Paravertebral/Retroperitoneal Malignant Tumors.

Dosimetric Assessment of CT-guided Radioactive Seed Implantation Assisted by 3D Printing Non-Coplanar Template in Treatment of Chest Malignant Tumor

Dosimetric Study of 3D-Printing Coplanar Template Combined with CT-guided 125I Seed Implantation for Treating Non-Small Cell Lung Cancer

Analysis of Position Errors of 3D Printing Individual Non-Coplanar Template for Radioactive Seed Implantation for Malignant Tumor

Dosimetry Verification of Radioactive Seed Implantation for Malignant Tumor Assisted by 3D-Printing Coplanar Template