Abstract:Lithium-sulfur (Li-S) batteries are widely regarded as the next-generation energy storage technology, due to their high potential in energy density and a low projected cost. Practical applications of such batteries are plagued with radical challenges that mainly stem from two factors. First, both sulfur and its final lithiation product, Li2S, are insulating. Thus, the reaction kinetics is slow and often leads to a low attainable capacity. Second, active material dissolve in the electrolyte in the form of lithium polysulfides. This dissolution causes a series of problems, including loss of cathode materials by diffusion away from the cathode, collapse of the cathode structure, and the polysulfide shuttle effect. As a result, Li-S batteries commonly show fast capacity decay and low coulombic efficiency. Herein, we report the exceptional battery performance of porous carbon-sulfur composite microspheres, PSC-S, that benefited from simultaneous control of nanostructure and microscale particle morphology. The porous carbon microspheres (PSC) was synthesized as the sulfur host,by combining emulsion polymerization and evaporation-induced self-assembly (EISA) process, with a good control of both pore structure and microscale particle morphology. Such material not only demonstrated superioty in attainable capacity, but also in several other critical parameters for the development of high-energy Li-S batteries. PSC-S composite boasts a high tap density of 1.08 g/ml and contains 75 wt.% sulfur embedded into the mesopores of its carbon framework. At a high sulfur loading of 5 mg-S/cm2 and 60wt.% sulfur content in the electrode, this material delivers both high gravimetric and high volumetric capacity with excellent retention. Carbon nanotubes (CNTs) can also be readily incorporated into the microspherical structure in the synthesis process to form a porous spherical carbon-carbon nanotube-sulfur composite (PSC-CNT-S). CNT incorporation effectively raises the conductivity of the composite, and thus significantly improves its high-rate performance. At a high current density of 2.8 mA/cm2, an initial capacity of 1100 mAh/g and a reversible capacity of 700 mAh/g after 200 cycles were achieved in PSC-CNT-S. The resultant areal capacity of over 3.5 mAh/cm2 is much higher than in previous reports of Li-S cathodes fabricated using coating techniques.

Effect of template ratio of porous carbon on the performance of lithium-sulfur battery

Preparation of mesoporous carbon and its effect on properties of lithium-sulfur batteries

Optimized Assembly of Micro-/Meso-/Macroporous Carbon for Li–S Batteries

Hierarchically Structured Sulfur/Carbon Nanocomposite Material for High-Energy Lithium Battery

Facile and Scalable Synthesis of Micro-Mesoporous Carbon/magnesium Oxide/sulfur Composite for Lithium-Sulfur Batteries

Effect of porous carbon carbonizing temperatureon the properties of Li-S batteries

Effect of Loading Methods on the Performance of Hierarchical Porous Carbon/sulfur Composites in Lithium Sulfur Batteries

Modified Nano-Caco3 Hard Template Method for Hierarchical Porous Carbon Powder with Enhanced Electrochemical Performance in Lithium-Sulfur Battery

Assembling Carbon Pores into Carbon Sheets: Rational Design of Three-Dimensional Carbon Networks for a Lithium Sulfur Battery

Nanoarchitectured Graphene/CNT@Porous Carbon with Extraordinary Electrical Conductivity and Interconnected Micro/Mesopores for Lithium‐Sulfur Batteries

Three-dimensional porous carbon composites containing high sulfur nanoparticle content for high-performance lithium–sulfur batteries

A hierarchical micro/mesoporous carbon fiber/sulfur composite for high-performance lithium-sulfur batteries

A Mixed Microporous/Low-range Mesoporous Composite with High Sulfur Loading from Hierarchically-structured Carbon for Lithium Sulfur Batteries

Mesoporous N-doped graphene prepared by a soft-template method with high performance in Li-S batteries.

Multifunction-balanced porous carbon and its application in sulfur-loading host and separator modification for lithium–sulfur batteries

Porous Carbon Architecture Assembled by Cross-Linked Carbon Leaves with Implanted Atomic Cobalt for High-Performance Li–S Batteries

3D Interconnected Crumpled Porous Carbon Sheets Modified with High-Level Nitrogen Doping for High Performance Lithium Sulfur Batteries

Sulfur‐Impregnated, Sandwich‐Type, Hybrid Carbon Nanosheets with Hierarchical Porous Structure for High‐Performance Lithium‐Sulfur Batteries

Mesoporous Carbon-Sulfur Composite Microspheres with Multiscale Morphology Control to Achieve High Areal Capacity for Lithium-Sulfur Battery Cathodes

High performance lithium-sulfur batteries using threedimensional hierarchical porous carbons to host the sulfur

Horizontally Aligned Lamellar Porous Graphene/nickel Composite for High Volumetric Capacity Lithium-Sulfur Batteries