Abstract:Lithium-sulfur (Li-S) batteries are widely regarded as the next-generation energy storage technology, due to their high potential in energy density and a low projected cost. Practical applications of such batteries are plagued with radical challenges that mainly stem from two factors. First, both sulfur and its final lithiation product, Li2S, are insulating. Thus, the reaction kinetics is slow and often leads to a low attainable capacity. Second, active material dissolve in the electrolyte in the form of lithium polysulfides. This dissolution causes a series of problems, including loss of cathode materials by diffusion away from the cathode, collapse of the cathode structure, and the polysulfide shuttle effect. As a result, Li-S batteries commonly show fast capacity decay and low coulombic efficiency. Herein, we report the exceptional battery performance of porous carbon-sulfur composite microspheres, PSC-S, that benefited from simultaneous control of nanostructure and microscale particle morphology. The porous carbon microspheres (PSC) was synthesized as the sulfur host,by combining emulsion polymerization and evaporation-induced self-assembly (EISA) process, with a good control of both pore structure and microscale particle morphology. Such material not only demonstrated superioty in attainable capacity, but also in several other critical parameters for the development of high-energy Li-S batteries. PSC-S composite boasts a high tap density of 1.08 g/ml and contains 75 wt.% sulfur embedded into the mesopores of its carbon framework. At a high sulfur loading of 5 mg-S/cm2 and 60wt.% sulfur content in the electrode, this material delivers both high gravimetric and high volumetric capacity with excellent retention. Carbon nanotubes (CNTs) can also be readily incorporated into the microspherical structure in the synthesis process to form a porous spherical carbon-carbon nanotube-sulfur composite (PSC-CNT-S). CNT incorporation effectively raises the conductivity of the composite, and thus significantly improves its high-rate performance. At a high current density of 2.8 mA/cm2, an initial capacity of 1100 mAh/g and a reversible capacity of 700 mAh/g after 200 cycles were achieved in PSC-CNT-S. The resultant areal capacity of over 3.5 mAh/cm2 is much higher than in previous reports of Li-S cathodes fabricated using coating techniques.

Optimized Assembly of Micro-/Meso-/Macroporous Carbon for Li–S Batteries

Hierarchically Structured Sulfur/Carbon Nanocomposite Material for High-Energy Lithium Battery

Facile and Scalable Synthesis of Micro-Mesoporous Carbon/magnesium Oxide/sulfur Composite for Lithium-Sulfur Batteries

3D Cotton-Pad-Like Hierarchically Porous Structure Stacked by Hexagonal Highly Graphitized Carbon Nanosheets as Sulfur Immobilizers for Li–S Batteries

Assembling Carbon Pores into Carbon Sheets: Rational Design of Three-Dimensional Carbon Networks for a Lithium Sulfur Battery

A hierarchical micro/mesoporous carbon fiber/sulfur composite for high-performance lithium-sulfur batteries

Sulfur-infiltrated porous carbon microspheres with controllable multi-modal pore size distribution for high energy lithium–sulfur batteries

A Mixed Microporous/Low-range Mesoporous Composite with High Sulfur Loading from Hierarchically-structured Carbon for Lithium Sulfur Batteries

Optimization of Microporous Carbon Structures for Lithium–Sulfur Battery Applications in Carbonate‐Based Electrolyte

A One-Step Hard-Templating Method for the Preparation of a Hierarchical Microporous-Mesoporous Carbon for Lithium-Sulfur Batteries

Amylose-Derived Macrohollow Core and Microporous Shell Carbon Spheres As Sulfur Host for Superior Lithium-Sulfur Battery Cathodes.

Porous Carbon Architecture Assembled by Cross-Linked Carbon Leaves with Implanted Atomic Cobalt for High-Performance Li–S Batteries

Activated Carbon with Ultrahigh Specific Surface Area Synthesized from Natural Plant Material for Lithium–sulfur Batteries

Carbon Foam Fibers with a Concentric Tube‐Core/Three‐Dimensional Nanosheet‐Sheath Structure for High‐Performance Lithium‐Sulfur Batteries

Synthesis and Characteristics of Nanoporous Carbon Spheres /S Composite as Cathode Material for Li-S Battery

Hierarchically Assembled Mesoporous Carbon Nanosheets with an Ultra Large Pore Volume for High-Performance Lithium–sulfur Batteries

Sulfur‐Impregnated, Sandwich‐Type, Hybrid Carbon Nanosheets with Hierarchical Porous Structure for High‐Performance Lithium‐Sulfur Batteries

A Series of Unique Carbon Materials for Lithium-Sulphur Batteries

High Sulfur Content Microporous Carbon Coated Sulfur Composites Synthesized Via in Situ Oxidation of Metal Sulfide for High-Performance Li/S Batteries

Carbon with hierarchical pores from carbonized metal–organic frameworks for lithium sulphur batteries

Mesoporous Carbon-Sulfur Composite Microspheres with Multiscale Morphology Control to Achieve High Areal Capacity for Lithium-Sulfur Battery Cathodes