Abstract:To reduce the structural deterioration of mass concrete structures from temperature cracks, and lower energy consumption caused by the traditional mass concrete hydration heat cooling process, this paper reports the preparation of concrete temperature-controlled phase change aggregate (PCA) by a vacuum compaction method using light and high-strength black ceramite and No. 58 fully refined paraffin wax as phase change material (PCM), and the encapsulation technology of the aggregate by using superfine cement and epoxy resin. Further, through laboratory tests, the cylinder compressive strength, thermal stability and mixing breakage rate of the encapsulated PCA were tested, and the differences in mechanical properties such as compressive strength, flexural strength and splitting tensile strength between phase change aggregate concrete (PCAC) and ordinary concrete were studied. A test method was designed to test the heat storage effect of PCA, and the temperature control effect of PCAC was analyzed based on the law of conservation of energy. The research conclusions are as follows: (1) Both superfine cement and epoxy resin shells increase the strength of the aggregate, with the epoxy resin increasing it more than the superfine cement. The thermal stabilization of the PCA is good after encapsulation of superfine cement and epoxy resin. However, PCA encapsulated in superfine cement is more easily crushed than that encapsulated in epoxy resin. (2) Under the condition of water bath heating and semi-insulation, when the water bath temperature reaches 85 °C, the temperature difference between the PCA and the common stone aggregate can be up to 6 °C. Based on the law of energy conservation, the test results will be converted to mass concrete with the same volume of aggregate mixture;, the difference of PCAC and ordinary concrete temperature can be up to 10 °C, so the temperature control effect is significant. (3) The mechanical properties of PCAC with 100% aggregate replacement rate compared to ordinary concrete are reduced to varying degrees, and the performance decline of the epoxy-encapsulated PCA is smaller than that encapsulated with superfine cement; in an actual project, it is possible to improve the concrete grade to make up for this defect.

Pr epar ati on of mi crocapsuI e phase change mat eri aI mort ar

Preparation and Characterization of Fatty Acid Ternary Eutectic Mixture/Nano-Sio 2 Composite Phase Change Material for Building Applications

Evaluation of the Potential Use of Form-Stable Phase Change Materials to Improve the Freeze-Thaw Resistance of Concrete

Enhanced thermo-mechanical properties of cementitious composites via red mud-based microencapsulated phase change material: Towards energy conservation in building

Temperature dependent effect of nano-scale phase change materials on fresh and hardened cement based mortar

Change of the Coefficient of Thermal Expansion of Mortar Due to Damage by Freeze Thaw Cycles

Characterization of Novel Shape‐stabilized Phase Change Material Mortar: Portland Cement Containing Na 2 SO 4 ·10H 2 O and Fly Ash for Energy‐efficient Building

A novel measurement method of thermal performances for an improved thermal storage concrete with microencapsulated phase change materials

Potential of Utilizing Form-Stable Phase Change Materials to Improve Freeze–Thaw Resistance of Mortar with Varying Water Content

Optimal Integration of Phase-Change Microcapsules and Nano-Silica for Improving the Strength of Phase-Change Concrete

Preparation and characterization of innovative cement mortar incorporating fatty acid/expanded graphite composite phase change material for thermal energy storage

Analysis of Freeze-Thaw Damage of Cement Mortars Doped with Polyethylene Glycol-Based Form Stable Phase Change Materials

Thermoregulation Performance and Mechanical Properties of Phase Change Asphalt Mortars

Thermophysical and Mechanical Properties of Hardened Cement Paste with Microencapsulated Phase Change Materials for Energy Storage

Experimental investigation on the influence of phase change materials on properties and pore structure of steam-cured mortar

Experimental investigation of thermal and mechanical characteristics of slag cement mortars with PCM for radiant floors

Experimental Investigation on a Novel Temperature-Controlled Phase Change Aggregate Concrete: Thermo-Mechanical Properties and Hydration Heat Control

Investigation on Hydration and Mechanical Properties of Mortar Containing Limestone Powder and Fly Ash Based on the Coupled Chemical–Thermal–Mechanical Method

Experimental study and assessment of thermal energy storage mortar with paraffin/recycled brick powder composite phase change materials

Experimental Investigation on the Effects of Phase Change Material and Different Ventilation Modes on the Thermal Storage, Space Heating and Energy Consumption Characteristics of Ventilated Mortar Blocks

SEM Analysis of the Interfacial Transition Zone between Cement-Glass Powder Paste and Aggregate of Mortar under Microwave Curing