Abstract:The cold drawing of magnesium wires has constantly been an obstacle in industrial manufacture due to the lack of sufficient independent slip system at ambient temperature and the frequent intermediate annealing gives rise to regrettably low production efficiency. Aiming at the technique challenge, a feasible and effective method of multi-pass cumulative cold drawing with small deformation per pass was utilized in this study and a wire of 0.625mm in diameter was obtained out of primitive Φ2.0mm material with the accomplishment of about 2.3 in cumulative strain (90% in area reduction), the efficiency of which was dramatically improved. The microstructure, texture and mechanical properties with the variation of cumulative area reduction were investigated. It can be apparently observed that continuous dynamic recrystallization had occurred during cold drawing. The outcomes are displayed as follows: the transition emerged from low angle grain boundary to high angle grain boundary; the increased fraction of undeformed/recrystallized structure first descended then ascended; the deformed structure initially appeared yet disappeared quickly. All of above owned an almost same critical point at around 23% cumulative area reduction. One of the most remarkable consequences of the deformation was the degeneration of the average grain size steadily from 11.8 to 3.1µm. 〈10-10〉//DD fiber component was gradually transformed from the primitive {0002}//DD fiber texture and this deformation texture was continuously strengthened. The enhanced mechanical properties achieved uncommonly high strength of 214.5MPa in yield strength and 256.9MPa in ultimate tensile strength due to grain refinement arising from continuous dynamic recrystallization and intense fiber texture strengthening introduced during cold drawing.

Hot extrusion-drawing technology of magnesium alloys welding wire and its deformation mechanism study

Microstructure evolution and mechanical property of Mg-Gd-Y-Zn-Zr alloy wires prepared by hot drawing

Fine-grained Structure and Recrystallization at Ambient Temperature for Pure Magnesium Subjected to Large Cold Plastic Deformation

Microstructure and Hot Deformation Behaviour of Twin-Roll Cast AZ31 Magnesium Wire

Microstructures, Textures and Mechanical Properties Evolution During Cold Drawing of Pure Mg

Phase transformation, texture evolution, and mechanical properties of Mg-9.5Gd-4Y-2Zn-0.3Zr alloy wires fabricated using hot drawing

Influence of Large Cold Strain on the Microstructural Evolution for a Magnesium Alloy Subjected to Multi-Pass Cold Drawing

Research on Hot Extrusion and Cold Drawing for Micro-Tube of Magnesium Alloys

Relating Residual Stress and Microstructure to Mechanical and Giant Magneto-Impedance Properties in Cold-Drawn Co-based Amorphous Microwires

Drawing Process and Properties of Roll-casting AZ31 Magnesium Alloy Sheet

Towards strength-ductility synergy through a novel technique of multi-pass lowered-temperature drawing in AZ31 magnesium alloys

Integrated Physical and Numerical Simulations of Weld Seam Formation During Extrusion of Magnesium Alloy

Effect of Grain Boundary Segregation on Microstructure and Mechanical Properties of Ultra-Fine Grained Mg–Al–Ca–Mn Alloy Wires

Effect of Hot Extrusion, Hard Drawing and Heat Treatment on Properties and Structure of Mb5b Wrought Mg Alloy

Uncovering the influence of deformation amount on microstructure evolution and mechanical behavior of the multi-DoF formed WE43 magnesium alloy

Superior Strength-Ductility Synergy of Mg-Nd-Zn-Zr Alloy Rod Achieved by Drawing at Elevated Temperatures

Process window and mechanical properties for thin magnesium- and zinc-wires in dieless wire drawing

Achieving Exceptional High Ductility in Binary Mg–6Zn Alloy Wire by Grain Boundary Strengthening and Twinning‐Induced Plasticity

Microstructure and mechanical properties of WE43 magnesium alloy fabricated by wire-arc additive manufacturing

Research Progress of Microstructure Characteristics and Mechanical Properties of Hot-Deformed Biodegradable Mg-based Alloys

Microstructure, mechanical and corrosion properties of Mg–Zn–Nd alloy with different accumulative area reduction after room-temperature drawing