Abstract:The cold drawing of magnesium wires has constantly been an obstacle in industrial manufacture due to the lack of sufficient independent slip system at ambient temperature and the frequent intermediate annealing gives rise to regrettably low production efficiency. Aiming at the technique challenge, a feasible and effective method of multi-pass cumulative cold drawing with small deformation per pass was utilized in this study and a wire of 0.625mm in diameter was obtained out of primitive Φ2.0mm material with the accomplishment of about 2.3 in cumulative strain (90% in area reduction), the efficiency of which was dramatically improved. The microstructure, texture and mechanical properties with the variation of cumulative area reduction were investigated. It can be apparently observed that continuous dynamic recrystallization had occurred during cold drawing. The outcomes are displayed as follows: the transition emerged from low angle grain boundary to high angle grain boundary; the increased fraction of undeformed/recrystallized structure first descended then ascended; the deformed structure initially appeared yet disappeared quickly. All of above owned an almost same critical point at around 23% cumulative area reduction. One of the most remarkable consequences of the deformation was the degeneration of the average grain size steadily from 11.8 to 3.1µm. 〈10-10〉//DD fiber component was gradually transformed from the primitive {0002}//DD fiber texture and this deformation texture was continuously strengthened. The enhanced mechanical properties achieved uncommonly high strength of 214.5MPa in yield strength and 256.9MPa in ultimate tensile strength due to grain refinement arising from continuous dynamic recrystallization and intense fiber texture strengthening introduced during cold drawing.

Microstructures, Textures and Mechanical Properties Evolution During Cold Drawing of Pure Mg

Microstructure Evolution and Properties of Mg-9Gd-0.8Al Alloy with Lamellar Phase During Extrusion at Different Temperatures

Fine-grained Structure and Recrystallization at Ambient Temperature for Pure Magnesium Subjected to Large Cold Plastic Deformation

Relating Residual Stress and Microstructure to Mechanical and Giant Magneto-Impedance Properties in Cold-Drawn Co-based Amorphous Microwires

Influence of Large Cold Strain on the Microstructural Evolution for a Magnesium Alloy Subjected to Multi-Pass Cold Drawing

Microstructure evolution and mechanical property of Mg-Gd-Y-Zn-Zr alloy wires prepared by hot drawing

Phase transformation, texture evolution, and mechanical properties of Mg-9.5Gd-4Y-2Zn-0.3Zr alloy wires fabricated using hot drawing

Achieving Ultrafine Grain Size in Mg-Al-Zn Alloy by Cold Drawing

Effect of Temperature on Microstructures, Texture and Mechanical Properties of Hot Rolled Pure Mg Sheets

Dynamic Recrystallization, Texture Evolution, and Improved Mechanical Properties of Mg-Y-Zn-V Alloy during Forging and Subsequent Extruding Deformation

Research on microstructure evolution and deformation mechanisms of fine-grained Mg alloys minitube during manufacturing process

Effect of Cold Deformation on Microstructure and Mechanical Properties of Mg-8Gd-3Y-0.5Zr Alloy

Superior Strength-Ductility Synergy of Mg-Nd-Zn-Zr Alloy Rod Achieved by Drawing at Elevated Temperatures

Effect of Grain Boundary Segregation on Microstructure and Mechanical Properties of Ultra-Fine Grained Mg–Al–Ca–Mn Alloy Wires

Experimental Analysis of Wire Drawing Influence on Microstructure, Texture, and Mechanical Properties of High‐Carbon Steel for Prestressing Strand

Effects of Grain Size, Texture and Twinning on Mechanical Properties and Work-Hardening Behaviors of Pure Mg

Microstructure Stability of Cold Drawn AZ31 Magnesium Alloy During Annealing Process

Microstructure, mechanical and corrosion properties of Mg–Zn–Nd alloy with different accumulative area reduction after room-temperature drawing

Evolution of Microstructure and Tensile Properties of Extruded Mg-4Zn-1Y Alloy

Microstructure and Texture Evolution of Mg-3Zn-1Al Magnesium Alloy During Large-Strain Electroplastic Rolling

Effect of cold rolling on the microstructure and mechanical properties of MG-8GD-3Y-0.5ZR alloy