Abstract:Grain refinement of Zr–containing Al alloys has attracted extensive attention for many years in both industry and academia, since "Zr–poisoning" phenomenon always happens when commercial refiner is applied in such alloys. This unrecoverable grain nucleating obstacle finally leads to poor grain refinement efficiency. In this work, a special Al–Ti–C master alloy rich in TiC nano–particles was applied to a high–strength Al–Zn–Mg–Cu–Zr alloy (i.e. 7050 alloy). The effects of TiC nano–particles on the microstructure and mechanical properties of 7050 alloy during solidification, hot extrusion and subsequent heat treatment were systematically investigated. The results show that prominent grain refinement occurs with TiC addition through both the growth restriction effect and heterogeneous nucleation. Meanwhile, TiC nano–particles are more inclined to distribute along grain boundaries than the interior of matrix grains after solidification. After subsequent homogenization and hot extrusion, TiC nano–particles tend to align along extrusion direction. In comparison with 7050 matrix alloy, the tensile properties especially ductility of 1% TiCp/7050 composite after heat treatment have been improved obviously. Furthermore, it is worth noting that precipitates in the composite have also been obviously refined. Synergetic effects of grain refinement, refined precipitates and increased dislocation density are responsible for the optimized mechanical properties of TiCp/7050 composite. This work provides new insights for controlling matrix grains of Zr–containing Al alloys and developing low–cost Al matrix composites.

Effect of nano TiC/Ti refiner addition on microstructure and properties of as-cast Al-Zn-Mg-Cu alloy

Effect of Al-5Ti-1B on Microstructure and Mechanical Properties of As-Cast Al-Zn-Mg-Cu Alloy

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Effects of Al-Ti-C Refiner and Forming Processes on the Microstructure and Properties of Al-Zn-Mg-Cu Alloys

Enhanced grain refinement and mechanical properties of a high–strength Al–Zn–Mg–Cu–Zr alloy induced by TiC nano–particles

Grain Refinement and Mechanical Properties of Cu-Cr-Zr Alloys with Different Nano-Sized TiCp Addition.

Study on Grain Refining and Metamorphism of ZL111 Aluminium Alloys

Effect of Ti content on microstructures and mechanical properties of cast Al-2Li-2Cu-0.5Mg alloy

Refinement Effectiveness of Self-Prepared (nbti)c Nanoparticles on As-Cast 1045 Steel

Influence of Al-Ti-B Addition on the Microstructure and Mechanical Properties of A356 Alloys

Effects of nano-sized TiB2 particles and Al3Zr dispersoids on microstructure and mechanical properties of Al–Zn–Mg–Cu based materials

Influence of TiCN addition on the microstructures and mechanical properties of the AZ31 alloy

Microstructures and Mechanical Properties of Al–Zn–Mg–Cu Alloy with the Combined Addition of Ti and Zr

The Evaluating Study of the Refining Effect of Al-Ti-C and Al-Ti-B on Aluminum

Grain Refinement of Al-5Ti-0.62C-0.2Nd Grain Refiner for Commercial Pure Aluminum and Its Effect on Mechanical Properties

STUDY ON THE MICROSTRUCTURES AND GRAIN REFINING PERFORMANCE OF Al-Ti-C GRAIN REFINING MASTER ALLOYS

Simultaneously Improved the Strength and Ductility of Cast Al-3Li-2Cu Alloy by Ti Addition and Heat Treatment

Effect Of La, Zr Micro-Alloying On The Microstructure And Mechanical Properties Of Al-5mg-0.2ti Alloy

Increased tensile strength and elongation of the Ni–Fe based polycrystalline cast superalloy via the trace addition of TiC nanoparticles

Microstructures and properties of AlZnMgCu alloys refined by nano Al3Ti‐TiB2‐AlN‐TiN/Al inoculant ribbons