Abstract:The use of carbon nanotubes (CNTs) as the reinforcing phase to prepare copper-based composite materials can improve the strength and high conductivity of copper-based conductors. In order to analyze the effect of surface oxidation modification on the structural properties of carbon nanotubes and its strengthening effect on composite materials, this article combines heterogeneous copolymerization liquid phase mixing method and spark plasma sintering molding method; prepares the carbon nanotubes/copper composite materials using carbon nanotubes under different oxidation treatment conditions as the reinforcing phase (the volume fraction of carbon nanotubes is 3%); and characterizes the microstructure, mechanical properties, and electrical and thermal conductivity of the composite material. Studies have shown that the tensile strength and hardness of composite materials first increase with the increase of CNT oxidation treatment time and then decrease with the increase of oxidation treatment time. When the oxidation treatment time is 4 h, CNTs are uniformly dispersed in the matrix while maintaining good structural integrity and load-bearing capacity, and the composite material has the highest mechanical properties. The tensile strength of the composite material made of 80‐ nm CNTs reaches 452.4 MPa, which is 1.6 times that of pure copper, and the hardness reaches 127.4HV, which is twice that of pure copper. The electrical conductivity and thermal conductivity of the composite material first increase with the increase of the oxidation treatment time of carbon nanotubes and then decrease with the increase of the oxidation treatment time. The 80 nm CNT reinforced composite material has better CNT dispersion performance and higher conductivity than that of 15 nm CNT preparation. The electrical conductivity of the composite material reaches the maximum value of 92% IACS when the CNT oxidation treatment time is 4 hours, which is 95% of the pure copper sample, and the electrical conductivity is significantly better than that of the CNT/Cu composite material and copper alloy prepared by other methods. The thermal conductivity of composite materials is lower than that of pure copper. The thermal conductivity of carbon nanotubes with an oxidation treatment time of 2 h decreases most obviously, indicating that the thermal resistance generated by the interface and agglomeration phases in the composite material affects its thermal conductivity.

Fabrication of CNTs/Cu ultrafine powders and composite materials

Microstructure and Properties of In-Situ TiC Reinforced Copper Nanocomposites Fabricated Via Long-Term Ball Milling and Hot Pressing

Study on Mechanical and Electrical Properties of High Content CNTs/Cu Composites

Progress of CNTs Reinforced Copper-based Composite Preparation

SYNTHESIS AND THE PERFORMANCE OF CARBON NANOTUBES-(Ni-P) COMPOSITES

Preparation of Cu-based composite materialsreinforced by nanotube by powder-metallurgy

Mechanical and Conductive Properties of Cu Matrix Composites Reinforced by Oriented Carbon Nanotubes with Different Coatings

Preparation method of carbon nano tube enhanced copper-based composite material

Preparation, microstructure and properties of Cu-8.3Al/CNTs composites with different volume fractions of CNTs

Optimization of the mechanical properties of CNTs/Cu composite by regulating the size of interfacial TiC

Preparation of Three-Dimensional Carbon Microtube/Carbon Nanotube Composites and Their Application in Supercapacitor

Improving comprehensive performance of copper matrix composite by spray pyrolysis fabricated CNT/W reinforcement

Effects of the addition of CNTs and Al alloying on the microstructure and properties of Cu-(Al)/CNTs composites

Research of Carbon Nanotubes-Cu Composite with Interpenetrating Networks

Effect of Surface Modification of Carbon Nanotubes on the Properties of High-Strength and High-Conductivity Copper Matrix Composites

A Study of Silver Decoration on Carbon Nanotubes via Ultrasonic Chemical Synthesis and Their Reinforced Copper Matrix Composites

Enhancement of mechanical properties and conductivity in carbon nanotubes (CNTs)/Cu matrix composite by surface and intratube decoration of CNTs

Preparation of Ultra-thin sandwich Cu-Cu/CNTs-Cu Composite Foil with High Tensile Strength by Electrodeposition

A novel approach for in-situ preparation of copper/graphene composite with high hardness and high electrical conductivity

New Preparation Technology of Copper Matrix Composites Reinforced by Short Carbon Fibers

A Powder Metallurgy Route to Fabricate CNT-reinforced Molybdenum-Hafnium-carbon Composites