Abstract:{10 (1) over bar1}-{10 (1) over bar2} double twin is the most common twin type being observed in the rolled AZ31 magnesium alloy, especially at low or moderate rolling temperature. Four types of rolled AZ31 magnesium alloy sheets were produced by rolling strong basal textured AZ31 plates at 150 degrees C and 300 degrees C respectively through different rolling paths by two passes till total reduction 17%. The rolling paths are normal and cross rolling respectively: the rolling directions of the two passes for normal rolling are mentally paralleled while perpendicular to each other for the cross rolling. Sheets are characterized in terms of microstructure and texture using optical microscope and scanning-electron microscope equipped with EBSD detector, and their mechanical performances are measured by uni-axial tensile tests at room temperature and a strain rate of 0.001 s(-1). Tensile samples are cut parallel or perpendicular to the final rolling direction to obtain the mechanical anisotropies. The effects of the {10 (1) over bar1}-{10 (1) over bar2} double twins occurred during rolling on the microstructure, texture and mechanical properties of the rolled sheets are discussed and related to each other. The results show that the fraction of {10 (1) over bar1}-{10 (1) over bar2} double twins varies widely in different rolled sheets, which are determined by the rolling temperature. The twins in different rolled sheets are arranged in different ways. In the normal rolled sheets, the traces of twins are approximately perpendicular to the final rolling direction, while in the cross rolled sheets there are both traces of twins parallel and to the final directions. This phenomenon is related to the variant selection of twinning during rolling deformation. And the variant selection law is related to the rolling direction. For the same reason, the textures of twins in the rolled sheets produced through different paths are different. The textures of twins will add onto the bulks, and increases the textural difference between the bulks. The differences between mechanical properties of the rolled sheets are also related to the different textures and microstructures of the sheets caused by twins.

Effect of Twinning and Detwinning on Mechanical Proprieties of AZ3 1 Magnesium Alloy

The effect of twinning and detwinning on the mechanical property of AZ31 extruded magnesium alloy during strain-path changes

Quasi-in Situ Electron Backscatter Diffraction Analysis of Twinning–detwinning Behavior in AZ31 Magnesium- Alloy Rolled Plates Subjected to Compression Loading in Different Directions

The Effects of Detwinning on the Mechanical Properties of AZ31B Magnesium Alloy with Different Strain Rates at 423 K

The effect of {10¯11}–{10¯12} double twinning on the microstructure, texture and mechanical properties of az31 magnesium alloy sheet during rolling deformation

Influence of Pre-Twinning on High Strain Rate Compressive Behavior of AZ31 Mg-alloys

Twinning Effects on the Hot Deformation Behavior of AZ31 Mg Alloy

The effect of {1011}-{1012} double twinning on the microstructure, texture and mechanical properties of AZ31 magnesium alloy sheet during rolling deformation

Microstructure, Texture and Mechanical Properties Evolution of Pre-Twinning Mg Alloys Sheets During Large Strain Hot Rolling

Twinning, Grain Orientation, and Texture Variations in Mg Alloy Processed by Pre-Rolling

Effects of Micro-Twin Lamellar Structure on the Mechanical Properties and Fracture Morphology of AZ31 Mg Alloy

The Effect Of {10(1)Over-Bar1}-{10(1)Over-Bar2} Double Twinning On The Microstructure, Texture And Mechanical Properties Of Az31 Magnesium Alloy Sheet During Rolling Deformation

Influence of Grain Orientation on Twinning During Warm Compression of Wrought Mg–3Al–1Zn

Twinning Behavior of a Strongly Basal Textured AZ31 Mg Alloy During Warm Rolling

EFFECT OF TWINNING ON MECHANICAL PROPERTY AND WORKABILITY OF Mg ALLOY

Influence of tensile twinning on electrochemical and corrosion behavior of Mg alloy

Effect of deformation conditions on twinning of AZ31 magnesium alloy during compression test

Microstructure Characterization of Twinning Under Impact Loading for AZ31B Magnesium Alloys

Analysis of the microstructure and deformation mechanisms by compression along normal direction in a rolled AZ31 magnesium alloy

Effect of initial orientation on the microstructure and mechanical properties of textured AZ31 Mg alloy during torsion and annealing

Influence of In-Plane Simple Shear Strain on the Grain Orientation Regulation and Stretch Formability of Pre-twinned AZ31 Magnesium Alloy Sheet