Abstract:Nanometer-sized particles, for example, TiO2, have gradually gained the attention to improve the mechanical and tribological properties of epoxy composite coatings. In the present paper, TiO2 with the size of 300 nm was applied to improve the reciprocating friction and wear performances of an epoxy composite. The effects of TiO2 content and sample preparation methods on the mechanical and tribological performances were investigated experimentally. It was found that the optimal mixture ratio of TiO2 was 4 wt%, and the tensile strength of composite increased by up to 30% compared with the control sample. The TiO2 nanoparticles were treated with polyvinylpyrrolidone (PVP) and then mixed into epoxy resin with three-roll mill grinding technique. The PVP molecules could surround a single TiO2 to form super-monomer, which produced repulsive force to aim to disperse nanoparticles, and the three-roll mill grinding could utilize the compression of axis surfaces and friction at different speeds to reduce the size of agglomerations of more than 5 microns. The results showed that the PVP molecules treatment could improve tensile strength and modulus, and three-roll mill grinding technique could enhance the elongation at break. In addition, the reciprocating wear rate and frictional coefficient of the epoxy composite plates also were reduced remarkably owing to the pretreatment of TiO2 particles, for example, and the frictional coefficient of epoxy composite decreased from 0.09 to 0.04 for the optimal ratio of TiO2, and special wear rate also decreased by 87.5% compared with the control sample. This was because the TiO2 nanoparticles acted as the stress transfer medium and could undertake part of loading to relieve stress directly into the epoxy matrix. There was a thin transfer film in which the particles acted as a membrane skeleton to avoid matrix further being torn. Because of the hardness and nanoeffect of particles, TiO2 could fill the defects in the wear interface to form a protective film and improve surface fatigue resistance property. The more uniform dispersion of TiO2 particles brought about the obvious improvement of wear resistance of composites.

The Inlfuence of Nano-TiO2on Properties of Epoxy Resin Coatings

Preparation and Properties of Nano-TiO2 Dispersion/Epoxy Coatings

Reciprocating Friction and Wear Performances of Nanometer Sized‐tio2 Filled Epoxy Composites

The Influence of Nano-AI_2O_3 Additive on the Adhesion between Epoxy Resin and Steel Substrate

The Effect of Nanoparticles on the Adhesion of Epoxy Adhesive

Effects of TiO2 Nanoparticles on the Overall Performance and Corrosion Protection Ability of Neat Epoxy and PDMS Modified Epoxy Coating Systems

STUDY ON THE PROPERTIES OF TiO2/EPOXY NANOCOMPOSITE

Effects of Functionalized Nano-TiO2 on the Molecular Motion in Epoxy Resin-Based Nanocomposites.

The influence of nanoparticles on the adhesion strength between epoxy resin and steel substrate

Effect of modified nanoTiO_2 on properties of coating and coated paper

Characterization of Protective Performance of Epoxy Reinforced with Nanometer-Sized TiO2 and SiO2

The Influence of Nano-Al2o3 Additive on the Adhesion Between Epoxy Resin and Steel Substrate

UV-curable Coatings with Nano-Tio2

Effect of nano-Al2O3 on adhesion strength of epoxy adhesive and steel

Effect of TiO2 Nano-concentrates on the Properties of Boron Phenolic-epoxy Coatings

A synergistic effect of nano-Tio2 and graphite on the tribological performance of epoxy matrix composites

Adhesion mechanism of steel and epoxy adhesive modified by nano-Al2O3

Study on Nano-Caco3 Modified Epoxy Powder Coatings

Effect of TiO 2 Nanofillers on the Mechanical and Abrasive Wear Properties of Epoxy Reinforced with Carbon Fabric Hybrid Composites

Investigation on Tribological and Thermo-Mechanical Properties of Ti 3 C 2 Nanosheets/Epoxy Nanocomposites

Preparation and Performance Study of Nano-Ti-MWCNT Hybrid Filler Reinforced Epoxy Resin Composite Coating