Abstract:Engineering ceramics have been widely used in modern industry for their excellent physical and mechanical properties, and they are difficult to machine owing to their high hardness and brittleness. Electrical discharge machining (EDM) is the appropriate process for machining engineering ceramics provided they are electrically conducting. However, the electrical resistivity of the popular engineering ceramics is higher, and there has been no research on the relationship between the EDM parameters and the electrical resistivity of the engineering ceramics. This paper investigates the effects of the electrical resistivity and EDM parameters such as tool polarity, pulse interval, and electrode material, on the ZnO/Al2O3 ceramic's EDM performance, in terms of the material removal rate (MRR), electrode wear ratio (EWR), and surface roughness (SR). The results show that the electrical resistivity and the EDM parameters have the great influence on the EDM performance. The ZnO/Al2O3 ceramic with the electrical resistivity up to 3410 Ω·cm can be effectively machined by EDM with the copper electrode, the negative tool polarity, and the shorter pulse interval. Under most machining conditions, the MRR increases, and the SR decreases with the decrease of electrical resistivity. Moreover, the tool polarity, and pulse interval affect the EWR, respectively, and the electrical resistivity and electrode material have a combined effect on the EWR. Furthermore, the EDM performance of ZnO/Al2O3 ceramic with the electrical resistivity higher than 687 Ω·cm is obviously different from that with the electrical resistivity lower than 687 Ω·cm, when the electrode material changes. The microstructure character analysis of the machined ZnO/Al2O3 ceramic surface shows that the ZnO/Al2O3 ceramic is removed by melting, evaporation and thermal spalling, and the material from the working fluid and the graphite electrode can transfer to the workpiece surface during electrical discharge machining ZnO/Al2O3 ceramic.

Study on E lectro-discharge M achining C haracteristics of Z rB 2-based U ltra-high T em perature C eram ics

The Effect Surface Roughness on Mechanical Properties of ZrB2 Based Ultra High Temperature Ceramic with WEDM

Study on Machining Method of Ultra High Tem perature Ceramic with Different Types Surface

Experimental Investigation of EDM Parameters for ZrB 2 -SiC Ceramics Machining

Study on the ZrB2-SiCw Ultrahigh Temperature Ceramics

Research and Development of ZrB2-based Ultra-high Temperature Ceramics

Investigation on Machining Performance of Micro-Holes EDM in ZrB 2 -Sic Ceramics Using a Magnetic Suspension Spindle System

Micro-EDM Drilling of ZrB2-SiC-graphite Composite Using Micro Sheet-Cylinder Tool Electrode

Electrical Discharge Machining (EDM) Phenomena of Insulating ZrO2 Ceramics with Assisting Electrode

Mechanical and plasma ablation properties of double-interface fibrous ZrB 2 -SiC ceramics for ultra-high-temperature application

Influence of Open-Circuit Voltage on High-Speed Wire Electrical Discharge Machining of Insulating Zirconia

Friction and Wear of Typical Tool Material at Elevated Temperature

Study on Ductile Grinding Character of Nano ZrO2 Ceramics using Ultrasonic Vibration Grinding

Study on Critical Ductile Grinding Depth of Nano Zro2 Ceramics by the Aid of Ultrasonic Vibration

Fabrication and Precision Electromachining Technology of ZrB2-SiC Ceramic Composites

Ablation behavior and mechanisms of 3D C<sub>f</sub>/ZrB<sub>2</sub>-SiC composite applied in long-term temperature up to 2400 C

Influence of electrical resistivity and machining parameters on electrical discharge machining performance of engineering ceramics

Progress in preparation and ablation resistance of ultra-high-temperature ceramics modified C/C composites for extreme environment

A Novel Development of Zrb2/Zro2 Functionally Graded Ceramics for Ultrahigh-Temperature Application

Ablation behaviors of ultra-high temperature ceramic composites

Mechanical properties of ZrB2/SiC/WC ceramic tool materials from room temperature to 1100 °C and cutting performance