Abstract:Subzone tensile tests were used to quantitatively study the tensile properties along the equal toughness welded joint of a 30Cr2Ni4MoV steel ultra-supercritical steam turbine rotor. The results show that the weld metal (WM) has lower strength than the base metal (BM) but similar plasticity and work hardening properties; the heterogeneous microstructure of the heat-affected zone (HAZ) results in a gradient distribution of tensile properties. By fitting the stress-plastic strain curve based on the Hollomon equation, there are two hardening exponents n 1 and n 2 in each subzone of the welded joint. Based on the K–M curve of the hardening rate, during uniform plastic deformation before necking, the coarse-grained HAZ (CGHAZ) only experienced two work hardening stages III and IV, and other micorregions of the welded joint exhibited three work hardening stages III ~V. The exponent n 1 represents initial hardening stage III when the plastic strain is less than 0.003, and n 2 represents hardening stages IV~V when the plastic strain is greater than 0.003. The uneven distribution of the exponent n 2 along the joint is related to the differences in the microstructure (tempered martensite or bainite) and carbides. Observing the subzone specimens after tensile testing by TEM, it can be found that dislocation cells appeared in the tempered bainite matrix, which had better work hardening capability than tempered martensite. The lath martensite and granular bainite mixed microstructure and fine granular martensite are beneficial for improving the hardening capabilities and delaying the hardening period, but the carbides distributed in the high-angle grain boundaries are not conducive to strain hardening. The microstructure type, grain size and carbides dispersed in the matrix are the main factors affecting the hardening behavior of each subzone of the joint. The strength prediction model of welded joint subzones based on the hardness and the hardening exponent was established.

Heterogeneous Mechanical Property and Microstructure of Welded Joints of CrMoV Steel

DIC/DSI Based Studies on the Local Mechanical Behaviors of HR3C/T92 Dissimilar Welded Joint During Plastic Deformation

Effect of Microstructure on Local Strain Hardening Behavior along an Equal Toughness Matching Welded Joint of a 30cr2ni4mov Welded Rotor

Microstructure and Mechanical Properties of Welded Joints of Cr18Ni30Mo2Al3Nb Alloy

Local Mechanical Properties of A Dissimilar Metal Welded Joint in Nuclear Power Systems

Evaluation of the Microstructure Related Strength of CrMoV Weldment by Using the In-Situ Tensile Test of Miniature Specimen

Research on the micro zone strength and strain hardening behavior in the 30Cr2Ni4MoV rotor welded joint

Influence of Microstructure on the Micro-Region Fracture Toughness of the 30cr2ni4mov Turbine Rotor Welded Joint

Research Methods of Mechanical Property Nonhomogeneity on Building Structural Steel Welding Joint

Study on Microstructure and Properties of Dissimilar Steel Welded Joints of FV520(B)

Microstructure and mechanical properties of dissimilar steel welded joint of martensite stainless steel and low alloy steel

Local Mechanical Properties and Microstructures of Alloy52M Dissimilar Metal Welded Joint Between A508 Ferritic Steel and 316L Stainless Steel

Microstructure and mechanical properties of dissimilar materials joints between T92 martensitic and S304H austenitic steels

Investigation of Local Brittle Zone in Multipass Welded Joint of NiCrMoV Steel with Heavy Section

Microstructure and mechanical properties of butt joints of QCr0.8／1Cr21NiSTi equal-thickness dissimilar materials by electron beam welding

The Microstructure and Mechanical Properties of Welded Joints of Hot-Rolled and Post-Weld Solution-Treated Fe-12.5Mn-9.8Al-1.0C Low-Density Steel

Formation, Microstructure, and Properties of Dissimilar Welded Joint between CrMnFeCoNi and Fe

High Cycle Fatigue Behavior of a Dissimilar Metal Welded Joint in Ultra-Supercritical Steam Turbine Rotor

A Study of the Performance of Dissimilar Pulsed-Laser-Welded JSC590R/JAC980YL Steel Joints of Differential Thickness

Microstructure Correlation and Fatigue Crack Growth Behavior in Dissimilar 9cr/crmov Welded Joint

Microstructures and Mechanical Properties of Friction-Stir Welding Joint of Al-Cu-Li Alloy