Abstract:Dissimilar metal welds (DMWs) between high-Cr martensitic heat-resistant steels and nickel-based alloys with nickel-based filler metals are widely used in fossil-fired power plants. Reports of premature failures of DMW joints have attracted considerable attention as such occurrences in the field can lead to significant economic loss and safety issues. Moreover, a comprehensive understanding of the high-temperature performance of new types of DMWs is lacking. In this work, creep tests were conducted over a stress range of 140-260 MPa at of 600 and 620 'C. A shift in the fracture location with variations in stress was observed, with three typical failure modes. At high stress levels (240-260 MPa), the DMW fractured in the base metal (BM) of martensitic steel, accompanied by a large degree of plastic deformation. At intermediate stress levels (200-240 MPa), the DMW fractured in the fine-grained heat-affected zone (FGHAZ) and the inter-critical heat-affected zone (ICHAZ), with creep cavities around coarsened carbides, indicating a typical type IV crack. At low stress levels (140-200 MPa), the DMW fractured in a mixed mode involving three stages. First, a crack initiated at the interface between the nickel-based weld metal and the martensitic steel, which was attributed to the interaction between the oxidation behavior of the martensitic steels and the thermal stress arising from the mismatch in the coefficients of thermal expansion. Second, the crack deflected into the FGHAZ/ICHAZ and developed into a type IV crack mode. Finally, the crack propagated into the adjacent BM, featuring significant plastic deformation. In addition, in the stress-LMP (Larson-Miller parameter) plot, the creep life at a relatively low stress level was shorter than that predicted by linear extrapolation of the data obtained at a high stress level, indicating a premature failure tendency at low stress. This premature failure tendency can be attributed to microstructure degradation in HAZs and preferential oxidation at the interface at low stress levels.

Microstructure Correlation and Fatigue Crack Growth Behavior in Dissimilar 9cr/crmov Welded Joint

Fatigue crack growth behavior of Ni-Cr-Mo-V steel welded joints considering strength mismatch effect

Fatigue Crack Growth Behavior of the MIG Welded Joint of 06Cr19Ni10 Stainless Steel

Near-threshold fatigue crack growth behavior of 10% Cr martensitic steel welded joint with 9% Cr weld metal in high temperature air

Investigation on the weakest zone in toughness of 9Cr/NiCrMoV dissimilar welded joint and its enhancement

Microstructure details and impact toughness for dissimilar 9Cr/CrMoV welded joints fabricated by NG-SAW and NG-TIG techniques

The Effect of Microstructure on the Fatigue Crack Growth Behavior of Ni-Cr-Mo-V Steel Weld Metal

Carbon diffusion in dissimilar joints between P91 and 12Cr1MoV steels welded by different consumables at high temperature

Investigation on the Fatigue Crack Propagation Behavior of L360MS Pipeline Steel Welded Joints with Inconel 625 Weld Metal

Microstructure and Mechanical Characteristics of Dissimilar TIG Welded 9% Cr Heat-Resistant Steels Joints

Mechanisms Affecting the Difference in Fatigue Resistance Between Welds and Base Materials Were Investigated Based on In-Situ Fatigue Method

Microstructure and Properties in Dissimilar/similar Weld Joints Between DP780 and DP980 Steels Processed by Fiber Laser Welding

Microstructural response at the interface and its effect on the fatigue fracture behavior of rotary friction welded dissimilar titanium alloys: Ti–5Al–2Sn–2Zr–4Mo–4Cr (Ti17) and Ti–6Al–2Sn–4Zr–2Mo (Ti6242)

In-situ SEM study of short fatigue crack propagation behavior in a dissimilar metal welded joint of nuclear power plant

Microstructure and Properties of ZGMn13Mo/A514 Dissimilar Steel Multi-pass Welding

Microstructure and Mechanical Properties of Weld-Bonded and Resistance Spot Welded Magnesium-to-steel Dissimilar Joints

Microstructure Evolution and Mechanical Properties of Laser Welded Dissimilar/Similar Joints Between Medium‐Mn Transformation‐Induced Plasticity Steel and DP980/22MnB5 Steels

Effect of Hydrogen Content and Microstructure Inhomogeneity on Fatigue Crack Growth Behavior of Ti-0.3Mo-0.8Ni Alloy Argon-Arc Welded Joints

Fracture Location Shift of Dissimilar Metal Welds under Coupled Thermal-Stress Effect

Microstructure, Hardness, and Residual Stress of the Dissimilar Metal Weldments of SA508-309L/308L-304L

Microstructure and fatigue performance of friction stir welded joints of 2A12‐T4 and 7075‐T6 dissimilar aluminum alloy