Abstract:The work aims to study effects of sliding speed, normal load and heating temperature on friction and wear properties of Ni-P/Ti/DLC multilayer films. Ni-P layer was plated on die steel substrates by adopting electroless nickel-phosphate plating process, and Ti transition layer and DLC protective layer were deposited by adopting filtered cathodic vacuum arc tech·60· 表面技术 2018 年 7 月 nology individually. Friction and wear properties of the multilayer films were evaluated in friction and wear experiments. Hardness, elastic modulus and composition of the multilayer films at different heating temperature were characterized based upon nanoindentation test and Raman spectrum detection. Wear track morphology and cross-sectional profile of the multilayer films were also analyzed with scanning electron microscope (SEM) and surface profile instrument. As the sliding speed increased, friction coefficient of the multilayer films decreased, and wear rate and volume first reduced and then increased. Friction coefficient of multilayer films changed slightly at different normal loads, and wear rate and volume increased as normal load increased. As the heating temperature increased, the friction coefficient of multilayer films decreased, and wear rate and volume first increased and then decreased. In addition, at higher heating temperature, graphite phase gradually increased on DLC layer of the multilayer films, hardness and elastic modulus tended to first increase and then decrease. At higher slide speed, graphitization trend of the DLC layer intensifies, friction coefficient changes greatly, width and depth of wear tracks increase greatly, and wear is worse. Soft Ti metal layer and hard DLC layer in multilayer films can effectively improve friction and wear properties at high load. As heating temperature increases, graphite phase gradually increases in DLC layer, and transfer film is easier to be generated in friction process.

Tribological Properties of Laminated WC/TiC Ceramic Cutting Tool Materials Sliding Against Bearing Steel

Wear Behaviour and Microstructural Changes of SiCw-Al Composite under Unlubricated Sliding Friction

Tribological behaviour of TiB2-HfC ceramic tool material under dry sliding condition

Studies of house dust mites can now fully embrace the "-omics" era.

Preparation of Ultra-Fine ATC Ceramics and Analysis of Its Dry-Sliding Wear Behavior

Friction and wear behaviors of Al 2 O 3 /TiC micro-nano-composite ceramic sliding against metals and hard materials

Wear mechanisms of Ti(C, N) ceramic in sliding contact with stainless steel

Wear Behavior of Al 2 O 3 -Ticn Composite Ceramic Sliding on Stainless Steel

Research On Wear Behavior Of Atc Cermet Material

Tribological performance of DLC-coated ceramics against cemented carbide under dry sliding conditions

Effects of Lubricants on Friction and Wear of Ti(Cn)/1045 Steel Sliding Pairs

Friction and Wear Properties of Ni-P/Ti/DLC Multilayer Films

Microstructure and tribological properties of laser cladded TiC reinforced WC-10Co4Cr coatings at 500 °C

ANALYSIS OF THE TRIBOLOGICAL PROPERTIES OF TiN/Si3N4 NANOCOMPOSITE COATING IN SLIDING CONTACT WITH CERAMIC, STEEL, AND POLYMER COUNTERPART

Tribological properties and wear resistance mechanism of WC-ZrO2-Al2O3 ceramics

Microstructure and High-Temperature Tribological Properties of Laser-Cladded WC10Co4Cr–xTi2AlC Coatings

Mechanical property and cutting performance of (W,Ti)C based ceramic composites with the addition of nano-sized CaF2

Study on the friction and wear performance of laser cladding WC-TiC/Ni60 coating on the working face of shield bobbing cutter

Friction and wear characteristics of plasma-sprayed WC coatings in dliding against GCr15 steel

Thermobarrier and antifriction properties of triboceramics on the surface of a cutting tool with (TiAlCrSiY)N/(TiAlCr)N coating during high-speed dry cutting

Tribological Properties of Additive Manufactured Ti6Al4V Against Cemented Carbide under Dry Sliding Conditions