Abstract:Hybrid electric vehicle (HEV) and plug-in hybrid electric vehicle (PHEV) require high power energy sources which are inexpensive and safe. Among various battery materials, 5V LiMn1.5Ni0.5O4 spinel materials are especially of interests for these vehicle applications because of their high operating voltage of ~4.7V and because manganese is inexpensive and less toxic than Ni and Co. However, the cycle life of these cathodes is inadequate and elevated temperature cycling cause rapid loss of capacity of the LiMn1.5Ni0.5O4 cells. This capacity degradation can be attributed to dissolution of Mn and Ni elements, solid electrolyte interphase (SEI) formation and electrolyte decomposition with high-voltage cycling [1]. Metal oxide coatings, which are usually synthesized by solution-based coating techniques, have improved capacity retention of the LiMn1.5Ni0.5O4 cells at the elevated temperatures and have been usually synthesized by solution-based coating techniques [2,3]. Recently, we have successfully coated nanometer thick amorphous lithium phosphorus oxyntirde (Lipon) electrolytes on the surfaces of LiMn1.5Ni0.5O4 and LiCoO2 particles by a RFmagnetron sputtering technique [4,5]. Uniform subnanometer thick Lipon improved the cycling behaviors of LiMn1.5Ni0.5O4 cells dramatically, but did not impede the Mn dissolution. Although a thicker Lipon layers of a few nanometers were effective in preventing the Mn dissolution, the Lipon layers greatly reduced the specific capacity because Lipon has a very low electronic conductivity of ~10 -14 S/cm. For comparison, nanometerthick protective films of electronic/ionic mixed conductor are being evaluated. Half-cell performances of cathodes fabricated with LiMn1.5Ni0.5O4 particles coated with mixed conductor will be reported for cycling at room and

Study on improvement of cycle performance of spinel LiMn2O4

Surface Modification and Electrochemical Properties of Li-Rich Layered Cathode Materials for Lithium-Ion Batteries

Cycling Stability of 5V LiMn1.5Ni0.5O4 Spinel Particles Coated with a Thin Film Mixed Conductor

Performance Improvement of Li-rich Layer-Structured Li1.2Mn0.54Ni0.13Co0.13O2 by Integration with Spinel LiNi0.5Mn1.5O4

Progress of modification study on LiNi0.5Mn1.5O4 cathode materials for lithium-ion batteries

Correlating Cycle Performance Improvement and Structural Alleviation in LiMn2-xMxO4 Spinel Cathode Materials: A Systematic Study on the Effects of Metal-Ion Doping

Improved electrochemical performance of spinel LiMn2O4 derived from manganese-based metal organic frameworks by organic ligands

Surface Modification and Characterization of Spinel LiMn2O4 Coated with MgO

Enhanced Cycling Performance of Spinel LiNi0.5Mn1.5O4 Cathodes through Mg-Mn Hetero-Valent Doping via Microwave Sol-Gel Method

Enhanced Cycling Stability of LiMn2O4 by Surface Modification with Melting Impregnation Method

Surface Modification Driven Initial Coulombic Efficiency and Rate Performance Enhancement of Li1.2Mn0.54Ni0.13Co0.13O2 Cathode

Improving the Electrochemical Performance of Li-rich Li1.2Ni0.2Mn0.6O2 by Using Ni-Mn Oxide Surface Modification

Improvement of Electrochemical Properties of LiNi0.5Mn1.5O4 Spinel Prepared by Radiated Polymer Gel Method

Tuning the Nanoarea Interfacial Properties for the Improved Performance of Li-Rich Polycrystalline Li-Mn-O Spinel.

Cycle Life Improvement of Limn2o4 Cathode in Rechargeable Lithium Batteries

Enhanced electrochemical performances of 5 v spinel LiMn 1.58Ni0.42O4 cathode materials by coating with LiAlO2

A Facile Method of Improving the High Rate Cycling Performance of LiNi1/3Co1/3Mn1/3O2 Cathode Material

Binding Li 3 PO 4 to Spinel LiNi 0.5 Mn 1.5 O 4 via a Surface Co‐Containing Bridging Layer to Improve the Electrochemical Performance

Boosting the Electrochemical Performance of a Spinel Cathode with the In Situ Transformed Allogenic Li-Rich Layered Phase

Surface Modification of High Voltage Spinel LiNi 0.5 Mn 1.5 O 4 Cathode Material Manufactured via Co-precipitation

Boosting the cycling performance of spinel LiMn2O4 by in situ MnBO3 coating