Abstract:Fluorinated organic-Inorganic hybrid materials were prepared using fluorine-containing monomers, silicone-containing monomers and tetraethyl orthosilicate by free-radical random copolymerization and sol-gel process, and applied as functional coatings onto aluminium alloy substrates. The fluorine-containing monomer used was dodecafluoroheptyl methyl acrylate (FA), and silicone-containing monomer used was vinyltriethoxy silane (VTES). Tetraethyl orthosilicate (TEOS) was added to pre-polymerized FA-co-VTES (PFAS) solution to cohydrolyze and co-condense with different addition values. The influence of inorganic component content (TEOS) on the physical properties of the coating films were characterized by FTIR, TGA, GPC, SEM, and XPS. The surface free energies of fluorinated organic-inorganic hybrid materials prepared were estimated from the contact angle data measured by sessile-drop method. Transparent coating films with smooth surface and uniform thickness could be obtained by the dip coating technique. FTIR and XPS results indicated that, owing to the strong electronegativity of the fluorine atoms, hydrophobic perfluoroalkyl groups were preferentially enriched to the outermost layer at the coating film-air interface, and three layers probably existed in the coating film. The upper layer oriented toward the air was composed of mainly perfluoroalkyl groups originating from FA, the intermediate layer was composed of hydrocarbon backbone chain originating from vinyl polymerization, and the bottom layer was composed of mainly -O-Si-O- network originating from TEOS. The fluorinated organic-inorganic hybrid materials prepared were very hydrophobic and exhibited excellent water repellency. It was demonstrated that the water repellency properties of PFAS/SiO2 hybrid materials was governed by hydrophobic perfluoroalkyl groups of the outermost layer. The contact angles of the coating films for water and methylene iodide were extremely high, at 120. 9 degrees and 93 degrees, respectively, for TEOS/FA mole ratios at 1 : 1, and their surface free energies were about 11.48 mJ/m(2). An important role of tetraethyl orthosilicate (TEOS) was to increase the density of the reaction sites of the -OH groups with the surface area and the thickness of fluorinated organic-inorganic hybrid coatings. It has been confirmed by FTIR and GPC results that the increase of TEOS amounts could enhance hydrolysis and condensation of alkoxide precursors to improve the adhesion between hybrid coating and aluminum substrates by the formation of Si-O-Al bonds. It was also testified that the increase of inorganic silica content had a significant effect oil the improvement of thickness of the bottom SiO2 layer, while it had a slight influence on the surface wettability of the hybrid coatings. The useful properties of fluorinated organic-inorganic hybrid coatings like better thermal stability and improved corrosion resistance,could be significantly enhanced by the improvement of thickness of the bottom SiO2 layer and bonding between SiO2 layer and aluminum substrates. Morphology analysis by SEM showed that the introduction of flexible organic phase could relax the stress and reduce the microcracks caused by the volume shrinkage of silicon network during heat treatment process. The thermal stability of fluorinated organic-inorganic hybrid materials studied by using TGA technique could be improved with TEOS amounts.The burning temperature should be less than 290 degrees C because the perfluoroalkyl groups begin to decompose from this temerature.

Preparation of Organic-inorganic Hybrid Superhydro-Phobic Coatings

Organic–inorganic Hybrid Superhydrophobic Surfaces Using Methyltriethoxysilane and Tetraethoxysilane Sol–gel Derived Materials in Emulsion

Preparation and Research of Hydrophobic PDMS/Nano-SiO2 Modified SiO2 Coating

rganic – inorganic hybrid superhydrophobic surfaces using ethyltriethoxysilane and tetraethoxysilane sol – gel derived materials in mulsion

Preparation of Organic-Inorganic Hybrid Superhydrophilic Coating for Aluminum Foil Conditioner

Preparation and Properties of Superhydrophobic Fluoroalkylsilane Coatings

The preparation and properties research of superhydrophobic organosilicone coating

Preparation and properties of hydrophobic organic-inorganic silica hybrid films

Preparation and properties of hydrophilic DEA/organosilane hybrid antifogging coating

Preparation of Epoxy-Silica-acrylate Hybrid Coatings

Facile Fabrication of Superhydrophobic Polymethyltriethoxysilane- Polymethylhydrosiloxane Coatings

Synthesis and Surface Properties of Fluorinated Organic-Inorganic Hybrid Coatings

Preparation of Durable Hydrophobic and Antireflective Silica Coating

Preparation of Superhydrophobic PMHS-SiO_2 Coatings by Sol-Gel Method

Synthesis of SiO_2/Organosilicone Hybrid Coating via Sol–Gel Method

Preparation of Superhydrophobic Silica Films by Sol-Gel Method and Its Wettability

Hydrophobic and Optical Properties of HMDS/Silica Hybrid Antireflective Coating Prepared via Sol-gel Method

Preparation and Superhydrophilic Mechanism of Porous TiO2/SiO2 Composite Thin Film

The Stability of Organic Silicone/SiO_2 Hybrid Coating by Sol-Gel Process

The stability of organic silicone/SiO2 hybrid coating by sol-gel proeess

Influence of Tetraethoxysilanes (TEOS) on the Interfacial Bond Strength Between Organic-Inorganic Hybrid Film and Substrate