Abstract:Dimethyl ether (DME) is a highly reactive diesel substitute that can be used as a pilot fuel to ignite low- reactivity methane (CH4) in heavy-duty engines. To optimize the efficiency and emissions of CH4/DME dual-fuel engines, it is crucial to study the fundamental combustion characteristics of DME mixed with methane. This study focuses on the influence of CH4 addition on the low-temperature oxidation (LTO) preparation stage and the thermal ignition (TI) preparation stage of DME in the two-stage ignition process, as these two stages respectively control the ignition delay of the first and second stages. The comparison is made between pure DME and a 50% CH4 and 50% DME blended fuel, operating under thermodynamic conditions representing the engine in- cylinder environment at 30 atm pressure, 650K temperature, and a stoichiometric equivalence ratio. The results show that the addition of methane hardly affects the control mechanism of the two-stage ignition of DME. Specifically, the LTO preparation stage is still promoted by the increase in OH radicals in the DME’s low-temperature oxygenation pathways to form KET, and the second stage is still controlled by the H2O2 loop mechanism. The kinetic analysis also reveals that methane addition can compete for some of the OH radicals in the LTO preparation stage, which has a suppressing effect on ignition. However, in the TI preparation stage, methane can promote the loop reaction of OH→HO2→H2O2→OH and promote ignition. For the operating conditions studied here, although methane consumes a total of 7.24% prior to thermal ignition, it only consumes 0.63% of the total amount in the LTO preparation stage and 1.81% of the total amount in the TI preparation stage. This indicates that methane is mainly consumed in the LTO stage, accounting for 65% of the total methane consumption amount. It can be concluded that the kinetic effect of methane has a relatively small impact on the ignition delay of the DME, at least for the conditions investigated here. In other words, the dilution and thermal effects caused by adding methane are the main reasons for the prolonged time of LTO/TI preparation. Overall, more fundamental research is warranted to understand the role of methane in the two-stage ignition process of DME, which could facilitate the development of CH4/DME dual-fuel engines.

Progress of Study on Combustion Process of Dimethyl Ether and Technological Trends

Numerical Investigation of Diesel Spray Combustion Characteristics in the Ammonia/air Atmosphere

Fuel Injection System Simulation for DME Engine

Study on injection characteristics of diesel and DME

Study on the performance and emissions of a compression ignition engine fuelled with dimethyl ether

Study on Combustion Characteristics of DME Fueled Diesel Engine

Simulation on Diesel/DME Mixed Injection System

Engine Performance and Emissions of A Compression Ignition Engine Operating on the Diesel-Methanol Blends

Combustion and Emission Characteristics of a DI Diesel Engine Fueled by Diesel-Methanol Blends

The Study on Preparation and Combustion of Diesel-Methanol Micro-Emulsified Fuel

Experimental study on Performances and combustion characteristics of DME powered vehicle

The Effect of Methane Addition on the Low-Temperature Oxidation Preparation and the Thermal Ignition Preparation of Dimethyl Ether under Representative Engine In-Cylinder Thermal Conditions

Study on Emission Characteristics of Direct Injection Diesel Engine Fueled with Dimethyl Ether

Investigation of the Effect of Ammonia Addition on the Two-Stage Ignition Process of Dimethyl Ether Based on Chemical Kinetic Analysis

Study on Combustion Characteristics of a DI Diesel Engine Operating on Diesel/Methanol Blends

Stage-wise Kinetic Analysis of Ammonia Addition Effects on Two-Stage Ignition in Dimethyl Ether

Research Progress on the Direct Dimethyl Ether Fuel Cell

A Study on Compression-Ignition Methanol Engine with Converted Dimethyl Ether as an Ignition Improver.

Experimental analysis on combustion, performance and emission characteristics of exo-THDCPD/diesel blends in a compression ignition engine

Improvement of Performance and Emissions of a Compression Ignition Methanol Engine with Dimethyl Ether