Abstract:High-pressure direct injection diesel/methanol dual-fuel engines exhibit excellent emission reduction potential, but they are still in the initial stage of research and development. The influences of different methanol injection locations, injection duration, and injection pressures on combustion characteristics, mixture homogeneity, and exhaust emissions are investigated to explore appropriate injection strategies and further optimize the engine performance base using CONVERGE software. The results show that the impact of the methanol injection position on the engine is relatively small, especially on combustion characteristics. A larger axial nozzle distance contributes to the formation of the homogeneous mixture, improving the engine economy. However, the engine performance is remarkably affected by methanol injection duration and methanol injection pressure. A shorter combustion duration is achieved with a decrease in the methanol injection duration and an increase in the methanol injection pressure, as a result of which the fuel economy is improved, with the combustion process more concentrated near the top dead center. Simultaneously, the mixture homogeneity is enhanced, which is conducive to a reduction in soot and CO emissions, yet not to a NOX and HC reduction. The lowest overall emissions of NOX, soot, CO, and HC are achieved when the radial nozzle distance and axial nozzle distance are 2.5 mm and 0.5 mm, respectively. Besides, the combustion characteristics and emissions of the engine are affected significantly under different methanol injection locations and injection pressures. The increased injection interval leads to deteriorating combustion characteristics and economy, i.e., a delayed combustion phase (CA50), an extended ignition delay and combustion duration (CA10–CA90), thereby increasing CO and soot emissions, but decreasing NOX emission. Additionally, the optimal economy and exhaust emissions are obtained when adopting an injection duration of 6 °CA and an injection pressure of 44.4 MPa. The ITE is increased in this case compared to the other injection strategies, thereby improving the engine performance significantly. The results provide parametric feedback and theoretical support for the design of high-pressure direct injection diesel/methanol dual-fuel engines from a time and space perspective, which has certain theoretical significance.

Experimental study on Performances and combustion characteristics of DME powered vehicle

Fuel Injection System Simulation for DME Engine

Numerical Investigation of Diesel Spray Combustion Characteristics in the Ammonia/air Atmosphere

Study on injection characteristics of diesel and DME

Simulation on Diesel/DME Mixed Injection System

Study on the performance and emissions of a compression ignition engine fuelled with dimethyl ether

Engine Performance and Emissions of A Compression Ignition Engine Operating on the Diesel-Methanol Blends

Combustion and Emission Characteristics of a DI Diesel Engine Fueled by Diesel-Methanol Blends

Study on Combustion Characteristics of DME Fueled Diesel Engine

An Experimental Study of the Combustion Process in a Natural-Gas Spark-Ignition Engine

Study on Emission Characteristics of Direct Injection Diesel Engine Fueled with Dimethyl Ether

Experimental study of effects of exhaust gas recirculation and combustion mode on combustion, emission, and performance of DME‐methanol ‐fueled turbocharged c ommon‐rail engine

Diesel Emission Improvements by the Use of Oxygenated DME/diesel Blend Fuels

The Effect of Methane Addition on the Low-Temperature Oxidation Preparation and the Thermal Ignition Preparation of Dimethyl Ether under Representative Engine In-Cylinder Thermal Conditions

An Experimental Study of the Dimethyl Ether (DME) General Spary Characteristics

Experimental Research on Gasoline Engine Fueled with DMF

Numerical Investigation on the Influence of Injection Location and Injection Strategy on a High-Pressure Direct Injection Diesel/Methanol Dual-Fuel Engine

Performance of A Direct Injection Diesel Engine Fuelled with A Dimethyl Ether/Diesel Blend

Experimental investigations of the effects of pilot injection on combustion and gaseous emission characteristics of diesel/methanol dual fuel engine

Optical Study on the Effects of Methane Equivalence Ratio and Diesel Injection Mass on Diesel-Ignited Methane Combustion Process

Study on the Performance of Diesel-Methanol Diffusion Combustion with Dual-Direct Injection System on a High-Speed Light-Duty Engine