Abstract:In this paper, the effect of the raw particle size and the annealing process on the compositions, microstructure, mechanical, thermal, and electrical properties of ZnO varistors was investigated using X-ray diffraction, infrared, X-ray photoelectron spectroscopy, scanning electron microscopy, electric field–current density, capacitance–voltage, mechanical, and thermal expansion measurements. Furthermore, the ZnO grain growth mechanism during the annealing process was discussed in detail. Results show that when the raw particle size equaled 90 nm and sintering was performed at 1100 °C for 2 h, the obtained ZnO-based varistors possessed excellent mechanical, thermal, and electrical properties; the E1mA, α, JL, and K values were 1015.3 V mm–1, 37.98, 2.45 μA cm–2, and 1.37, respectively, due to the highest bulk density and the finest uniform particle size distribution. When annealing occurred at 300 °C for three times, values of σf, KIC, E1mA, α, JL, and K reached 175.35 MPa, 1.96 MPa m1/2, 1180.2 V mm–1, 43.58, 2.15 μA cm–2, and 1.2, indicating improvements of approximately 14.7%, 4%, 16.2%, 14.7%, − 12.2%, and 11.11% compared with those of the non-annealed ZnO-based varistors, respectively, being due to the improved uniformity of grain size distribution and the re-distribution of donor Al3+ and Y3+ in the ZnO crystal and grain boundary. The annealing process lead to the transformation of Sb3+ to Sb5+ in the ZnO crystal, which could generate two additional coordination sites. The newly generated sites could combine with O2- in other crystals to increase the grain growth, resulting in clear grain growth on the surface, improved grain size distribution, and regular grain shape in the interior of ZnO-based varistors.

Effect of Dewatering Regime on Particle Aggregation of Synthetic Additive for ZnO Varistor

Reliability enhancement of zinc oxide varistors using sputtered silver electrodes.

Preparation of Composite Additives Powder by Coprecipitation Method and Investgation of ZnO Varistor Ceramics

The Effect of ZnO Powder Particle Distribution on Performance of Multilayer Chip Varistor

Preparation and electrical properties of multilayer ZnO varistors with water-based tape casting

Effect of additive particle size on degradation behavior of ZnO varistors under high current surges

Effect of SiO_2 Doping Content on Varistor Properties of ZnO

Influence of Rare-Earth Oxide Additives on Electrical Performance of ZnO Varistor

Excellent Electrical Properties of Zinc-Oxide Varistors by Tailoring Sintering Process for Optimizing Line-Arrester Configuration

High voltage gradient zinc oxide varistors for line surge arresters and GIS tank-type arresters

Influence of High Voltage Gradients on Electrokinetic Dewatering for Wenzhou Clay Slurry Improvement

Effects of Zn2SiO4 doping on the properties of zinc oxide varistors

Effects of raw particle size and annealing on microstructure, electrical and mechanical behaviors of ZnO-based varistors

Fabrication of High Performance Multilayer Zno Varistors with Chemically Synthesized Doped Zinc Oxide Powder

Effect of Co-Doping of Al3+, In3+, and Y3+ on the Electrical Properties of Zinc Oxide Varistors under Pre-Synthesizing BiSbO4

Improving Age Stability and Energy Absorption Capabilities of Zno Varistors Ceramics

The effect of ZnO particle size on the dynamic mechanical, thermal, and dielectric properties of ZnO varistor-Epoxy composites

Novel ZnO Varistors for Dramatically Improving Protective Effect of Surge Arresters

Dopant Effects to Pores in ZnO Varistors

Comprehensive Performances of ZnO Varistors Tailored by Multi-elements Doping

Characterisation of Zno-Based Varistors Prepared from Nanometre Precursor Powders