A Digitally Controlled and Variable Gain Amplifier

夏建生,陈国联

DOI: https://doi.org/10.3969/j.issn.1674-4888.2001.01.024

2001-01-01

Abstract:A digitally controlled CMOS variable gain amplifier base on R-2R ladder resistance network is introduced. The gain of amplifier can be adjusted by the digitally controlled word, and gain step size can be easily changed.

What problem does this paper attempt to address?

An Ultra-low Noise Variable Gain Amplifier with Accurate dB-Linear Characteristic

Bingtian Chen,Yufeng Zhang,Jianxiong Xi,Lenian He

DOI: https://doi.org/10.1109/icecs49266.2020.9294852

2020-01-01

Abstract:In this paper, a high-performance dB-linear variable gain amplifier (VGA) based on gain interpolation is introduced. The VGA core uses a resistor ladder as an attenuator to get different attenuation steps of the input signal. By smoothly moving the gain from one step to the next step, an accurate dB-linear gain characteristic is achieved. A low noise amplifier and a post amplifier are integrated to get lower noise and ensure high linearity, respectively. The chip is fabricated in a 180nm SiGe process and occupies a die area of 1.15mm(2). The total gain range is 48dB and the measured gain error is less than 0.27dB. The whole VGA consumes 30mA current from a 5V supply and the bandwidth is 120MHz. The measured in-band input referred noise density is 1nV/root Hz and the measured OIP3 is 33dBm.
A novel accurate dB-linear control circuit topology for variable gain amplifiers in BiCMOS technology

Zhenghao Lu,Changhui Hu,Xiaopeng Yu,Weimeng Lim,Yang Liu,Kiatseng Yeo

DOI: https://doi.org/10.1109/ISICir.2011.6131989

2011-01-01

Abstract:We present in this paper a novel accurate decibel linear control circuit topology for variable gain amplifiers. According to our knowledge, the proposed linear-in-dB control circuit features the simplest control mechanism and topology for current summing or current steering VGAs to date. Based on the proposed circuit topology, a wideband variable gain amplifier with accurate linear-in-dB gain variation is implemented in Tower Jazz 0.18μm SiGe BiCMOS technology. The simulation shows the designed wideband VGA operates up to 5.2GHz with a linear-in-decibel gain ranging from -50dB to +20dB. The VGA possesses nearly constant bandwidth over the gain variation range and dissipates about 6mA current from a single 1.8V supply. The simulated noise figure at maximum gain is less than 6.5dB when matched to 50Ω and the chip layout area is less than 0.3mm excluding pads.
A Wideband BiCMOS Variable Gain Amplifier with Novel Continuous Db-Linear Gain Control and Temperature Compensation

Zheng Hao Lu,Xiao Peng Yu,Kiat-Seng Yeo

DOI: https://doi.org/10.1007/s10470-016-0891-1

IF: 1.321

2016-01-01

Analog Integrated Circuits and Signal Processing

Abstract:In this paper, we present an accurate analog decibel linear control circuit for variable gain amplifiers (VGAs). The proposed circuit features simple and effective dB-linear control for current steering VGAs. A novel temperature compensation circuit is also proposed for this VGA. Based on the proposed circuit design techniques, a wideband single stage VGA with accurate analog dB-linear gain control and temperature compensation is realized in Tower Jazz 0.18 μm SiGe BiCMOS technology. The measurement result shows the proposed VGA S 21 gain is tunable from −50 to +20 dB with a −3 dB bandwidth of about 4.6 GHz. The measured IIP3 is from −29 to −8 dBm for maximum and minimum gain respectively and dissipates about 11 mA current from a single 1.8 V supply. The measured noise figure at maximum gain is about 8.5 dB when matched to 50 Ω and the VGA performance is insensitive to temperature variation when measured from −40 to +80 °C.
Design of Differential Variable-Gain Transimpedance Amplifier in 0.18 Μm SiGe BiCMOS

Samuel B. S. Lee,Hang Liu,Kiat Seng Yeo,Jer-Ming Chen,Xiaopeng Yu

DOI: https://doi.org/10.3390/electronics9071058

IF: 2.9

2020-01-01

Electronics

Abstract:This paper presents two new inductorless differential variable-gain transimpedance amplifiers (DVGTIA) with voltage bias controlled variable gain designed in TowerJazz’s 0.18 µm SiGe BiCMOS technology (using CMOS transistors only). Both consist of a modified differential cross-coupled regulated cascode preamplifier stage and a cascaded amplifier stage with bias-controlled gain-variation and third-order interleaving feedback. The designs have wide measured transimpedance gain ranges of 24.5–60.6 dBΩ and 27.8–62.8 dBΩ with bandwidth above 6.42 GHz and 5.22 GHz for DVGTIA designs 1 and 2 respectively. The core power consumptions are 30.7 mW and 27.5 mW from a 1.8 V supply and the input referred noise currents are 10.3 pA/√Hz and 21.7 pA/√Hz. The DVGTIA designs 1 and 2 have a dynamic range of 40.4 µA to 3 mA and 76.8 µA to 2.7 mA making both suitable for real photodetectors with an on-chip photodetector capacitive load of 250 fF. Both designs are compact with a core area of 100 µm × 85 µm.
A 0.96-mW dB-Linear Variable Gain Amplifier With 0.4-dB Linearity Error Over a 62.4-dB Gain Tuning Range

Liying Cai,Zhenghao Lu,Zhong Tang,Xiaopeng Yu

DOI: https://doi.org/10.1109/LSSC.2022.3213055

2022-01-01

IEEE Solid-State Circuits Letters

Abstract:This letter presents a low-power dB-linear variable gain amplifier (VGA) with a small linear-in-dB error over a wide gain tuning range. An exponential current ratio is realized in the linear-in-dB control circuit based on the subthreshold I-V characteristic. The VGA is built with subthreshold common-gate transistors as current steering, accurately replicating the exponential current ratio and forming a tunable gain. Implemented in 55-nm CMOS technology, the proposed VGA occupies a compact active area of 0.011 mm(2) excluding the buffer. It achieves a linear-in-dB error of 0.4 dB over a gain tuning range of 62.4 dB, corresponding to the state-of-the-art relative error of 0.6%. The proposed design shows constant 80-MHz bandwidth with a power consumption of 0.96 mW.
Linear-in-decibel Variable Gain Amplifier Design in 0.18µm SIGE BICMOS Technology

Muting Lu,Thangarasu Bharatha Kumar,Xiaopeng Yu,Kiat Seng Yeo

DOI: https://doi.org/10.1109/icsict.2016.7998855

2016-01-01

Abstract:This paper presents recent design techniques and performance tradeoffs for wideband variable gain amplifiers (VGA). A VGA design with reduced bandwidth variation over the entire gain control range is proposed and the incorporating design techniques are explained along with good simulation performance. The proposed five-stage VGA is designed in a commercial 0.18μm SiGe BiCMOS technology achieving a variable gain range from -47.3 to 27.3-dB, a 3-dB bandwidth better than 1.7-GHz, both input and output return losses greater than 10 dB, consuming 23.4mW using 1.8V supply voltage over the entire gain control range, and has a core circuit area of 240μm × 50μm.
Broadband matching variable-gain low-noise amplifier

Xu Zhiwei,Li Min,Li Nayu,Wang Shaogang,Zhang Zijiang,Gao Huiyan,Yu Xiaopeng

2019-01-01

Abstract:The invention relates to the technical field of integrated circuits, in particular to a broadband matching variable-gain low-noise amplifier. The gain of the low-noise amplifier can be flexibly adjusted through control of electric signals. Compared with a traditional low-noise amplifier, the low-noise amplifier has broadband impedance matching performance of the input end and the output end, and is suitable for occasions where broadband radio frequency receiving signals need to be processed.
A Wideband Digital Variable Gain Amplifier with DC Offset Cancellation in SiGe 0.18µm BiCMOS Technology

Muting Lu,Thangarasu Bharatha Kumar,Dawei Zhang,Xiaopeng Yu,Kiat Seng Yeo

DOI: https://doi.org/10.1109/isicir.2016.7829702

2016-01-01

Abstract:This paper presents a five-stage wideband digital controlled variable gain amplifier (DVGA). A bandwidth extended technique is proposed in this design to enhance gain flatness and enlarge gain range in high operating frequency. DC offset cancellation in this design helps to enhance the performance of proposed DVGA. The design is simulated using a commercial 0.18μm SiGe BiCMOS technology. The DVGA has a simulated gain range of 64.7 dB with a 3-dB bandwidth from 3 MHz to 3.55 GHz, an output 1-dB gain compression point better than -5.2 dBm, an input return loss better than 11.9 dB, an output return loss better than 18 dB, and a dc power consumption for core DVGA circuit of 3.7 mW from a 1.8-V supply.
A Linear-in-Decibel Automatic Gain Control Amplifier with Dual Mode Continuous Gain Tuning

Liying Cai,Xiong Song,Zhenghao Lu,Xiao-Peng Yu,Kiat-Seng Yeo,Jer-Ming Chen,Bharatha Kumar Thangarasu

DOI: https://doi.org/10.1109/tcsi.2023.3268216

2023-01-01

Abstract:A reconfigurable fully integrated automatic gain control (AGC) amplifier is presented which is based on a dual mode continuous gain adjustment variable-gain amplifier (VGA). The VGA is realized based on the current-steering structure, achieving a linear-in-dB gain tuned by AGC’s feedback voltage. A current division active load is proposed, which provides additional gain control range and realizes gain robustness to process and supply variations without extra calibration. Simulated with Cadence IC, the maximum gain variations due to process and supply variations are 3.5 dB and 2.6 dB, respectively. By using dual mode gain tuning technique, the VGA achieves a total gain range of 68.2 dB. Both bandwidth and gain of the VGA are adjusted independently. The AGC is realized in UMC 55-nm CMOS technology with 0.026 mm 2 core area. With the current division ratio K of 0.5, the proposed VGA achieves a linear-in-dB gain of 42.2 dB (−30.0 to 12.2 dB) with less than 0.79 dB error. The −3 dB bandwidth can be adjusted from 80 MHz to 140 MHz and is insensitive to gain variations. The power dissipation is from 2.9 mW to 4.5 mW. This design features bandwidth scalability and the gain independent of bandwidth to achieve various applications.
A 2.5 Gb/s CMOS Low Noise Transimpedance Amplifier with Active Feedback

韩良,刘晓宁,白涛,李华

DOI: https://doi.org/10.3969/j.issn.1000-3819.2008.03.022

2008-01-01

Abstract:Based on the analysis of the topology of every preamplifier,a CMOS common-gate(CG) transimpedance amplifier,which can be used in 2.5 Gbit/s optical communication system,is presented.In order to reduce the input equivalent noise current and enlarge the-3 dB bandwidth,an active feedback and active inductor are used instead of conventional resistor feedback.Measured results show the transimpedance gain is 61.8 dB,the bandwidth is 2.01 GHz,the input equivalent noise current is 9.5 pA/Hz and the power consumption is only 3.02 mW.
A CMOS High Dynamic Range Variable Gain Amplifier

郑吉华,李永明,陈弘毅

DOI: https://doi.org/10.3969/j.issn.1674-4926.2003.08.019

2003-01-01

Abstract:A CMOS novel variable gain amplifier (VGA) suitable for wireless broadband receiver with superheterodyne architecture was presented. The prototype chip was implemented by TSMC 0.18 μm technology. Simulations and measurements show that the VGA's gain control range is -28-42 dB; the operation frequency is up to 600 MHz; the minimum noise figure is 7.65 dB, and the IIP3 at the minimum gain setting is 20 dBm. The VGA dissipates 12 mA under a single 3 V power supply.
A CMOS High Linearity Variable Gain Amplifier

王自强,王志华

DOI: https://doi.org/10.3969/j.issn.1003-353x.2004.11.019

2004-01-01

Abstract:A variable gain amplifier (VGA) working at intermediate frequency (IF) for wirelessreceiver is presented. It consists of an operational amplifier (op-amp) and resistor feedback networks.The distortion of close loop amplifier is analyzed. It reduces the distortion of large output signalsmainly by improving the linearity of output impedance. The fully differential VGA is designed inKorean Dongbu 0.25μm CMOS technology. The power supply is 3.3V. While the differential out-put is 2Vpp, the distortion is less than -80dB, the power consumption is 3mW.
A Broadband Linear-In-Decibel Variable Gain Amplifier with Low Gain Error

Nan Lin,Fei Fang,Zhi-Liang Hong,Hao Fang

DOI: https://doi.org/10.1007/s10470-013-0079-x

IF: 1.321

2013-01-01

Analog Integrated Circuits and Signal Processing

Abstract:A new circuit architecture for broadband digitally controlled variable gain amplifier (VGA) is introduced in this paper. The gain of the VGA is controlled precisely by using a resistor ladder attenuator and a closed-loop fine gain control block together. The bandwidth of the VGA is extended by applying a compensation technique in the fine gain control block. Implemented in 0.13-μm CMOS technology, the proposed VGA demonstrates a decibel-linear gain range of 24 dB (0–24 dB) with a gain step of 0.1 dB, a gain error <0.08 dB, a maximum input-referred third-order intercept point (IIP3) of 22.8 dBm, and a 3-dB bandwidth of 600 MHz.
Low Power,high Linearity CMOS Programmable Gain Amplifier

Ziqiang Wang

2006-01-01

Abstract:Variable gain amplifiers(VGA) used in the front ends of receivers need to amplify large signals with high linearity.An amplifier was designed with an improved gm-boost circuit and increased transconductance of the input metal oxide semiconductor(MOS) transistor which reduces the distortion caused by the drain-source voltage variation.A symmetrical variable resistor structure was used to further reduce the non-linearity from the MOS switch.Simulation results show that the amplifier consumes 1.5 mW at 3.3 V.The total harmonic distortion of a 3.3 V differential output signal is less than-60 dB for frequencies from 1 to 10 MHz and voltage gains from 3 to 24 dB.
A 3.6V Rail-to-Rail Operational Amplifier with Constant G M

Chang Gao,Qiang Li,Jing Wang,Yasuaki Inoue

2015-01-01

Abstract:A 3.6V CMOS rail-to-rail operational amplifier with a novel constant g m (transconductance) biasing circuit is proposed. The rail-to-rail input stage is realized by connecting two complementary differential pairs in parallel. To obtain constant g m across the whole common mode input range, the drain currents of differential pairs are precisely controlled by proposed biasing circuit. This design is verified by simulation using a 0.18㎛ CMOS process. Simulation result shows a rail-to-rail input/output range and a constant g m with ±2.45% variation. Also an open loop gain of 88dB, unity gain bandwidth of 1.17MHz and phase margin of 63° are achieved.
A CMOS Programmable Gain Amplifier with Accurate Gain Control

FANG Fei,LIN Nan,FANG Hao,HONG Zhiliang

DOI: https://doi.org/10.3969/j.issn.1000-3819.2011.05.013

2011-01-01

Abstract:A CMOS programmable gain amplifier(PGA) with accurate gain control is realized in 0.13 μm RF CMOS process.Based on the conventional resistive attenuator,a new gain control method is proposed here.Using two overlapped feedback loops,the accurate gain control is achieved by changing the ratio of trans-conductance.Measurement results show that,with a supply voltage of 1.2 V,the power consumption is 24 mW and the-3 dB bandwidth is 600 MHz.In the gain range of 24 dB,0.08 dB gain accuracy can be obtained,the IIP3 for 0 dB and 24 dB is 18.8 dBm and-5.57 dBm respectively.
A Robust Rail-to-Rail CMOS Operational Amplifier

唐长文,张洁,闵昊

DOI: https://doi.org/10.3969/j.issn.1004-3365.2002.01.012

2002-01-01

Abstract:A robust rail-to-rail operational amplifier is presented, in which a new robust constant g m rail-to-rail input stage is employed. This new circuit is robust in that it does not require transconductance parameter matching n- and p-channel transistors for specific technology. Meanwhile, a front-feed Class AB control is aslo developed to ensure large dynamic range and strong driving capability. The whole circuit is simulated in 0.35 μm Alcatel and 0.6 μm Wuxi-Shanghua technology at 2.7 V power supply, respectively. The circuits have achieved a maximum transconductance deviation less than 7 % and 14 %, DC gain of 87.9 dB and 78.4 dB, unit gain bandwidth of 14 MHz and 9 MHz,and a phase margin of 67° and 75°, respectively.
A 0.8-3GHz 40dB dynamic range CMOS variable-gain amplifier

Xingli Huang,Xi Qin,Yajie Qin,Hao Fang,Zhiliang Hong

DOI: https://doi.org/10.1109/ASICON.2011.6157383

2011-01-01

Abstract:A wideband variable gain amplifier which provides 40dB dynamic gain range using dual-loop feedback Cherry-Hooper topology is presented. A modified negative capacitive neutralization technique is proposed to improve the frequency response with a reasonable cost of power consumption. This VGA is implemented in SMIC 0.13μm 1P8M CMOS technology, and occupies 0.3 mm 2 active area. The measurement results show that its -3dB bandwidth is from 800MHz to 3GHz. It consumes 21.6 mW at 1.2V power supply. The maximum input P 1dB with a preceding LNA is -27dBm at an overall gain of -0.5dB. © 2011 IEEE.
Design of Low-Power/Low-Voltage High Gain Amplifier

DENG Li,WU Xiao-bo

DOI: https://doi.org/10.3969/j.issn.1004-3365.2007.05.027

2007-01-01

Abstract:Based on 1.5 μm BCD technology,a low-voltage/low-power and high gain operational amplifier was proposed,which could operate at 1.8 V supply voltage.Multi-stage differential cascade structure and common-mode feedback loop were adopted.Stability of the circuit was greatly improved by using double nested Miller compensation technology.A quiescent current-controlled class AB output stage minimized quiescent current and decreased crossover distortion while rail-to-rail output swing was implemented.Test results showed that anticipated performances were achieved.The op-amp has an open loop DC gain of 96.3 dB at 5 V supply voltage,and in closed loop applications with 10 V/V gain,the circuit has a-3 dB bandwidth of 45 kHz,a gain error of ±0.06% and a quiescent current less than 60 μA.

A Digitally Controlled and Variable Gain Amplifier

An Ultra-low Noise Variable Gain Amplifier with Accurate dB-Linear Characteristic

A novel accurate dB-linear control circuit topology for variable gain amplifiers in BiCMOS technology

A Wideband BiCMOS Variable Gain Amplifier with Novel Continuous Db-Linear Gain Control and Temperature Compensation

Design of Differential Variable-Gain Transimpedance Amplifier in 0.18 Μm SiGe BiCMOS

A 0.96-mW dB-Linear Variable Gain Amplifier With 0.4-dB Linearity Error Over a 62.4-dB Gain Tuning Range

Linear-in-decibel Variable Gain Amplifier Design in 0.18µm SIGE BICMOS Technology

Broadband matching variable-gain low-noise amplifier

A Wideband Digital Variable Gain Amplifier with DC Offset Cancellation in SiGe 0.18µm BiCMOS Technology

A Linear-in-Decibel Automatic Gain Control Amplifier with Dual Mode Continuous Gain Tuning

A 2.5 Gb/s CMOS Low Noise Transimpedance Amplifier with Active Feedback

A CMOS High Dynamic Range Variable Gain Amplifier

A CMOS High Linearity Variable Gain Amplifier

A Broadband Linear-In-Decibel Variable Gain Amplifier with Low Gain Error

Low Power,high Linearity CMOS Programmable Gain Amplifier

A 3.6V Rail-to-Rail Operational Amplifier with Constant G M

A CMOS Programmable Gain Amplifier with Accurate Gain Control

A Robust Rail-to-Rail CMOS Operational Amplifier

A 0.8-3GHz 40dB dynamic range CMOS variable-gain amplifier

Design of Low-Power/Low-Voltage High Gain Amplifier