Abstract:This article describes a much simplified, Digital and analog mixed architecture that support general S-band transponder operation. The mass is reduced to under 1.4kg (including TCXO), and the dimension is about 170 *70*100mm. The power consumption is less than 11W measured in the side of 28V input with 1W SSPA transmitter output. The mass cut down is benefit mainly from the progress of digital design techniques and the improvement of the FPGA technologies. The designer implements the IF command and tracking demodulation by a 3 million system gates FPGA. Furthermore, the device is employed with tri-mode-redundancy. The algorithm of the main carrier tracking is based on phase lock loop, the command demodulation is based on Costas loop for sub carrier tracking and DTTL loop for bit synchronization. The carrier acquisition threshold is under -128 dBm with PM/BPSK demodulation losses < 1dB. The dynamic range is from -128 dBm to -55 dBm. The second technique that decreases the complexity is the structure of RF front-side. We use a small size saturated amplifier replacing the AGC amplifier, the saturation amplifier depresses the mostly of the signal dynamic and DSP deal with the dynamic left. We select a low power A/D converter with working frequency under 3Msps in under-sampling mode; however, the IF frequency is about 9.3MHz that can diminish the order of RF front-side down converter and the difficulties of analog band pass filter design. For the standard of the USB transmitter is only support modulation type: BPSK/PM, so we build a RF-IF close loop transmitter architecture that eliminate the components used in up converter architecture, the saved mixers and band pass filters extremely reduce the amount and the volume of PCB. Moreover, we creatively put the coherent forwarding signal generator and the Frequency-Phase Detector together in FPGA. The digital phase noise or jitter is wonderfully filtered by a well-designed analog low pass loop filter. To conclude, there is not any DAC or RF-filter in transponder's transmitter loop. The other advantage is that we can adjust the modulation index easily by digital parameter. The transponder developed by NSSC is under flight verification.

Analog Front-end Circuit Design of Transmitter Used in ETC

A 17.7–19.2-Ghz Receiver Front End with an Adaptive Analog Temperature- Compensation Scheme

A Ka-band 8-Element 4-Beam Transmitter Front End with Hybrid VGA and Symmetrical Transformer-based Doherty PA

The Design of All-Digital Polar Transmitter Based on ADPLL and Phase Synchronized ΔΣ Modulator

A Sub-1-GHz Band High-Dynamic-Range Receiver with Integrated Self-Adaptive Multipart AGC Loops

A CMOS 135–150 GHz 0.4 dBm EIRP transmitter with 5.1dB P1dB extension using IF envelope feed-forward gain compensation

A 2 GS/s 14-Bit Current-Steering DAC in 65 Nm CMOS Technology for Wireless Transmitter

A 0.7-8 GHz High IF Frequency-Extended Transmitter Front-End with −47.1-Db EVM at 16 QAM in 65-Nm CMOS

A 0.5-8Ghz Reconfigurable CMOS RF Receiver Front-end for CR and DPA Applications

A Modulation Depth and Output Power Tunable 5.8-Ghz Cmos Direct-Conversion Transmitter

A Novel Cmos Transmitter Front-End For Mobile Rfid Reader

A Fully Integrated Digital Polar Transmitter with Single-Ended Doherty PA and DLL-Based Three-Segment Hybrid DTC in 28 Nm CMOS

Digitally Equalized CMOS Transmitter Front-End with Integrated Power Amplifier

A RF Signal Generator for All-digital Transmitter

A Fully Integrated CMOS Transceiver for Mobile UHF RFID Reader

Design and Analysis of Analog Front-End of Passive RFID Transponders

A 0.13µm CMOS 1.5-to-2.15ghz Low Power Transmitter Front-End for SDR Applications

Front-End Development for Radar Applications: A Focus on 24 GHz Transmitter Design

A CMOS Power Amplifier with 100% and 18% Modulation Depth for Mobile RFID Readers

Analysis and Design of a 1.8–2.7 GHz Tunable 8-Band TDD LTE Receiver Front-End

A creative architecture for mass-sensitive transponder