Performance Analysis of High-Speed Digital Interface USB and IEEE 1394

Yang LI,Jian-hua ZOU

DOI: https://doi.org/10.3969/j.issn.1002-8684.2001.01.012

2001-01-01

Abstract:The basic features of Universal Serial BusUSB and IEEE 1394 are analyzed and compared in this paper and the foreground of the two interfaces are described.

What problem does this paper attempt to address?

Design and Implementation of the High-Performance Link Layer in High-Speed Serial Communication

Yong-jian TANG,Le-nian HE,Xiao-lang YAN

DOI: https://doi.org/10.3969/j.issn.1000-7180.2005.04.037

2005-01-01

Abstract:The USB2.0 supports the high-speed signaling at 480 Mbps. It can meet the needs of image and voice signal transmitting. In this paper, after demonstration of the characters and functions of high speed digital circuit of USB2.0 link layer, a novel design and implementation method of data recovery circuits, which is based on all digital phase-looked loop (ADPLL), for the full-speed mode, as well as a new approach of parallel implementation of the encode/decode module in high-speed mode were proposed. The simulation results indicated that the circuit has reached 480MHz. A FPGA hardware simulation system was developed, in which the functions of link layer was verified.
Research on USB Data Transmission Technology Based on LabVIEW

程龙飞,何闻

DOI: https://doi.org/10.3969/j.issn.1001-3881.2009.07.036

2009-01-01

Abstract:The USB data transmission technology based on LabVIEW was studied.The USB interface circuit which core chip is PDIUSBD12 produced by PHILIPS,the firmware programming method of the USB interface circuit,and the specific method of compiling application which is based on the LabVIEW were introduced.The result in the data transmission test shows that it can realize the data transmission between superior monitor and inferior computer by using LabVIEW and USB interface.
A Novel Physical-Layer Transceiver Used in USB2.0 Serial Data Link

Li Haoliang,He Lenian,Wang Zi,Yan Xiaolang

DOI: https://doi.org/10.1007/s11767-004-0246-4

2006-01-01

Abstract:The paper proposes a novel transceiver in physical layer for high-speed serial data link based upon Universal Serial Bus (USB) 2.0, comprising transmitter and receiver. In the design, transmitter contains pre-and-main driver to satisfy slew rate of output data, receiver includes optimized topology to improve precision of received data. The circuit simulation is based on Cadence’s spectre software and Taiwan Semiconductor Manufacture Corporation’s library of 0.25μm mixed-signal Complementary Metal-Oxide Semiconductor (CMOS) model. The front and post-simulation results reveal that the transceiver designed can transmit and receive high-speed data in 480Mbps, which is in agreement with USB2.0 specification. The chip of physical-layer transceiver has been designed and implemented with 0.25μm standard CMOS technology.
Design of Data Communication Interface of Data Acquirement System Based on USB

陈章位,赵玉刚

DOI: https://doi.org/10.3321/j.issn:1004-132X.2004.20.014

2004-01-01

Abstract:An interface based on USB is designed for Data Acquirement System with DSP chips. Cypress EZ-USB technology and FPGA technology were used in this interface. This kind of interface can achieve high speed data communication between the Data Acquirement System and the PC in the USB 1.1 protocol, and it can meet the requirements of high speed and real-time requirements.
The Design of How to Access 1394 Devices Through USB Interfaces

杨登峰,冯志华,张平,李龙雨

DOI: https://doi.org/10.3969/j.issn.1000-7180.2004.06.011

2004-01-01

Abstract:This paper introduces the theory of how to transfer data packet between USB interface and 1394 interfaces, and how to convert the data format from 1394 to USB.
Research and Discussion on High Speed Data Transmission of USB2.0

LIU Si-jiu,ZHAO Wei

DOI: https://doi.org/10.3321/j.issn:1002-8331.2007.02.021

2007-01-01

Computer Engineering and Applications Journal

Abstract:Based on the problems in the application of the high speed data transmission with USB2.0,the paper analyzed the reasons which affect the speed such as protocol overhead,bandwidth distribution,the host pc's software and hardware,device driver program and so on.The paper also introduces the endpoint FIFO pipe and GPIF.Furthermore,some experiments for data transmission in different mode have been done with USB2.0 device using EZ-USB FX2.Then some strategies are brought forward which can solve the high speed data transmission in the summary.
Real-time Bidirectional Data Transmission Based on USB Interface

Kuang Wang

2005-01-01

Abstract:The article designs a real-time bidirectional transmission channel.And it introduces the theory of the design,selects specific chip,introduces the hardware of the channel,and brings forward the method of designing USB firmware,driver,and application.
Research on Real-Time USB Driver Based on Linux Operating System

WANG Yi-hua,HUANG Dao-ping,LIU Shao-jun

DOI: https://doi.org/10.3969/j.issn.1001-2265.2011.01.021

2011-01-01

Abstract:In high-speed data acquisition systems and high-speed and high-accuracy numerical control systems,two important factors that may influence the performance of the systems are real-time capability and data transferring interfaces that connect systems.The standard Universal Serial Bus(USB),which has many advantages(including the advantage of data transferring) over other buses,is the dominating bus that is currently widely used.The paper focuses on discussing the realization of the realtime USB driver.Firstly,the structure of the USB subsystem in Linux operating system is introduced.Secondly,the realization of the realtime USB driver is discussed in detail.Finally,the performance of the USB driver is tested through a specified program.As is shown by the result,the realtime USB driver performs well and can meet the requirements of many highspeed data acquisition systems.The research work of the real-time USB driver presents brilliant application prospect and great practical value.
Realization of High-speed Data Transmission Based on USB Interface

吕超,张玉霞,王立欣

2009-01-01

Abstract:USB interface has the advantage of plug-and-play, easy to install, high-bandwidth, easy to expand and high-speed transmission. Despite the USB2.0 specification has reached the highest transmission speed of 60MB/s, but a lot of USB 2.0 devices actually worked in the data transmission quite different from it. The data acquisition system has been designed with FPGA as a central controller and CY7C68013 as a interface in this paper. When the interface chip CY7C68013 work at Synchronization slave FIFO mode, a block synchronization signal is designed to ensure the stability and highest transmission. The highest data transfers speed of the system is 31.8MB/s.
Design of IEEE 1394b Bus Link-layer Controller

Shuai Yang

2015-01-01

International Journal of Research Studies in Computer Science and Engineering

Abstract:Abstract: The IEEE 1394 bus has advantages such as high transmission speed, long transmission distance, plug and play, supporting variable transmission modes and so on. This essay mainly focuses on study link layer in the bus protocol and data transfer in asynchronous and isochronous mode, design the control chip for IEEE 1394b link layer, implements the design on RTL-level programming and verify the design through software simulation. Main work completed consists of: analyzes the protocol structure of link layer, physical layer of IEEE 1394b bus, defines the link layer control chip’s function and system structure divided into modules. Implement the design of modules with RTL programming and simulates the design in software.
Design of the IEEE-1394 Based System for Video Transmission

HUO XiaoXin,LIU XiangYang,ZHU Peisheng

2009-01-01

Abstract:In combination with the requirements of high capacitance information transmission of Avionics System,taking advantage of IEEE-1394b serial bus high-speed transmission characteristics,the paper designs a high-speed video transmission system based on IEEE-1394b serial bus.And it focuses on the overall design ideas and methods of the system,including design of main circuit.Experiment shows that the system successfully realizes the transmission of airborne video data.The system hardware is easy to be realized,process rate is fast,and has high speed of transmission.
Analyse of Optical Bus Real-time Basing on IEEE—1394b

XU Chang-bin,WANG Jian-hua

DOI: https://doi.org/10.3969/j.issn.1671-1815.2012.21.045

2012-01-01

Abstract:The IEEE—1394b interconnect system static isochronous transmission model and dynamic model are focused on the two models are obtained under the average waiting time of message mathematical expression.Pointed out IEEE—1394b interconnect system influence the real-time characteristic factor,and the analysis results are simulated.Key parameter message average waiting time is IEEE—1394b fiber optical bus interconnection system real-time research focus.The IEEE—1394b interconnect system real-time characteristics is introduced,focus of the isochronous and asynchronous transfer model of the messages the average waiting time of mathematical expression.Through simulated the isochronous transmission of asynchronous transmission has a great influence.
Design and Realization of Low Cost USB Protocol Converter

杨章顺,冉立新

DOI: https://doi.org/10.3969/j.issn.1000-3428.2004.18.069

2004-01-01

Abstract:USB has become popular due to its high speed, plug and play feature and the capability to avoid resource conflict. An embedded converter from other low speed bus to USB is very interesting, since it would allow legacy peripheral devices to experience USB advantages without major changes. The paper presents a universal USB1.1 protocol converting scheme, and an example of PS/2-USB converter is also given.
Implementation of Double IEEE 1394b Serial Bus Controller Based on the RapidIO

LIANG Qing,LUO Jin-sheng

DOI: https://doi.org/10.3969/j.issn.1000-8829.2013.05.018

2013-01-01

Abstract:The 1394b bus network systems,1394b logic design architecture and hardware platform of dual 1394b bus controller based on RapidIO architecture are introduced.On the platform,the 1394b drive and RapidIO drive based on Vx Works operating system are designed,1394b network test platform is built.Finally,the fundamental functions of the two channels 1394b bus controller are verified.The system interconnection among chips is implemented,as well as computer communications between the root node and the leaf node under the mode at the speed of 100 Mbit/s and 400 Mbit/s.
High-Speed Data Acquisition System Base On Usb

Y Wang,Zm Wu,Bf Zhao

2002-01-01

Abstract:The high-speed data acquisition system based on USB (Universal Serial Bus) includes a computer loaded testing platform software, A/D converter, micro-controller and communication interface of USB, and can rapidly and accurately transmit data collected. In circuit design except analogue circuit, memory and microprocessor, nearly all-logical circuit can be realized by PLD (Programmable Logic Device), which improve the system integration, and transform the design of hardware into design of software, and increase the speed of exploitation and reliability of system.
Designs of the High-speed Data Acquisition System Based on USB and I2S Bus

LI Long-yu,FENG Zhi-hua,LIU Zhi-gang,ZHANG Chang-hui

DOI: https://doi.org/10.3969/j.issn.1001-2257.2005.05.016

2005-01-01

Abstract:This paper addresses a frame of highspeed data acquisition system which based on USB and I~2S bus.The using of highspeed data acquisition chip AD7862 and CPLD(complex programmable logic device) make the system adjustable.This method may be a good way for the D/A、DI/DO etc.
The Design and Development of USB 2.0 Interface IP Core

RUAN Li-hua,WANG Xiang,HUANG Quan-ping,ZHOU Rong-zheng,HONG Zhi-liang,JIANG Feng-xian

DOI: https://doi.org/10.3969/j.issn.0427-7104.2005.01.034

2005-01-01

Abstract:An IP core design of USB 2.0 interface is presented. The stress is put on the digital circuit implementation of USB 2.0 Protocol Controller, Buffer Controller and Work Mode Controller. The circuit can operate at both USB high-speed (480 Mbps) and full-speed (12 Mbps) rates. In order to achieve high-speed transaction request of (USB 2.0) and reduce the design complexity of the hardware, a structure of combining MCU firmware and hardware is proposed. A double-buffered structure is adopted in the design to reduce the hardware cost. The proposed structure of USB 2.0 interface has been verified with FPGA.
Design of Data Transmission System Based on FPGA and USB 2.0

Junsheng Wu,Fuzhou Shang,He Sun,Tian Qin,Qing Li

DOI: https://doi.org/10.4028/www.scientific.net/amm.321-324.417

2013-01-01

Applied Mechanics and Materials

Abstract:In this paper, a high-speed data transmission system based on FPGA (Field Programmable Gate Array) and USB 2.0 (Universal Serial Bus) technology is designed. Firstly, we introduce the hardware of the data transmission system, which includes data acquisition circuit, transmission circuit and power conversion circuit, etc. Secondly, the corresponding software design including USB firmware program, USB driver and firmware modification are described in detail. Finally, the corresponding experiment has been carried out, which show that the developed system will help to achieve the data transmission system with the characteristics of high-speed, integration and low power consumption, etc.
Universe Serial Bus (USB)

黄维柱,许军

DOI: https://doi.org/10.3969/j.issn.1001-3695.2001.02.015

2001-01-01

Abstract:Traditional interfaces of external peripherals have manyshortcomings，so they are not consistent with the requirements of the PC now. The newly-come Universal Serial Bus has many advantages, such as: high speed, ease-of-use, ease to expand port, supporting plug-play, low-cost etc, so it is used very widely now. This paper just describes some main features of USB.
Design and Implementation of FPGA Based High-Speed Bus for Control System

MI Xiao-ling,HUANG Wen-jun,JIN Jian-xiang,SHI Yi-ming

DOI: https://doi.org/10.3785/j.issn.1008-973x.2011.11.026

2011-01-01

Abstract:The system architecture of high-speed bus was studied to improve the control system communication speed and efficiency.A FPGA based high-speed bus applied in control system was designed and implemented,which is high real-time,high throughput,easy to expand and so on.The physical layer was based on multipoint-low-voltage differential signaling(M-LVDS) standard to achieve 256 Mbps serial communication.Multi-path optimization selection network redundancy through real-time link state maintenance was used in data link layer to ensure reliable communications while maximizing bandwidth utilization.The design was implemented on Xilinx XC3S400A FPGA and actual tests were done.Results show that communication speed and real-time performance are improved significantly compared with the current mainstream bus of control system,and the needs of upper applications are met to the greatest degree.

Performance Analysis of High-Speed Digital Interface USB and IEEE 1394

Design and Implementation of the High-Performance Link Layer in High-Speed Serial Communication

Research on USB Data Transmission Technology Based on LabVIEW

A Novel Physical-Layer Transceiver Used in USB2.0 Serial Data Link

Design of Data Communication Interface of Data Acquirement System Based on USB

The Design of How to Access 1394 Devices Through USB Interfaces

Research and Discussion on High Speed Data Transmission of USB2.0

Real-time Bidirectional Data Transmission Based on USB Interface

Research on Real-Time USB Driver Based on Linux Operating System

Realization of High-speed Data Transmission Based on USB Interface

Design of IEEE 1394b Bus Link-layer Controller

Design of the IEEE-1394 Based System for Video Transmission

Analyse of Optical Bus Real-time Basing on IEEE—1394b

Design and Realization of Low Cost USB Protocol Converter

Implementation of Double IEEE 1394b Serial Bus Controller Based on the RapidIO

High-Speed Data Acquisition System Base On Usb

Designs of the High-speed Data Acquisition System Based on USB and I2S Bus

The Design and Development of USB 2.0 Interface IP Core

Design of Data Transmission System Based on FPGA and USB 2.0

Universe Serial Bus (USB)

Design and Implementation of FPGA Based High-Speed Bus for Control System