Abstract:Rare-earth-doped SiAlON and Si3N4 materials from aluminosilicate starting materials have been reported to show superior photoluminescence (PL) properties. Three different starting materials, including pulverized coal furnace fly ash, diatomite and raw illite, were used for synthesis of nitride materials. The phase and morphology evolution of these products were carefully monitored at the low temperature range of 1350 °C to 1450 °C by X-ray diffraction (XRD), scanning electronic microscopy (SEM) and Fourier-transform infrared spectroscopy (FT-IR). The PL properties of Eu-doped nitride products were also comparatively characterized. The results show that the type of starting material affects the phase composition and the photoluminescence properties of products. The existence of aluminum and alkali metals could effectively promote nitridation reactions. Aluminum in the starting materials led to the formation of different aluminum-rich nitride phases. Thus, β-SiAlON could be achieved at a much lower temperature (1350 °C) using raw illite or fly ash containing the proper amount of aluminum. Additionally, excess aluminum led to the formation of corundum and 15R-SiAlON. The products from pulverized coal furnace fly ash had more prismatic particles, and the products from diatomite had more fibrous particles. With the progress of the nitridation process, the fibers were increased, becoming longer and straighter, and the prismatic particles were more obvious. The presence of aluminum in the starting materials led to a blue shift in the photoluminescence spectrum.

Controllable Synthesis of High-purity β-SiAlON Powder

Controllable Synthesis of High-purity β-SiAlON Powder: Controllable Synthesis of High-purity β-SiAlON Powder

Controllable Synthesis Of High-Purity Beta-Sialon Powder

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Synthesis of AlON Powder by Aluminothermic Reduction and Its Thermodynamic Analysis

Synthesis of single phase β-SiAlON ceramics by reaction-bonded sintering using Si and Al2O3 as raw materials

Effects of Al2o3 Phase Composition on Alon Powder Synthesis Via Aluminothermic Reduction and Nitridation

Solid-state NMR and XRD study of α-SiAlON powders prepared by combustion synthesis

Facile and Economical Preparation of SiAlON-Based Composites Using Coal Gangue: from Fundamental to Industrial Application

Thermodynamic study and syntheses of β-SiAlON ceramics

Synthesis of β-SiAlON-SiC composites from coal gangue based β-SiAlON

Synthesis of β-SiAlON materials from blast furnace slag by acetic acid leaching combined with carbothermal reduction and nitridation

Oxidation Behavior of Β-Sialon Powders Fabricated by Combustion Synthesis

Carbothermal Reduction Nitridation of Fly Ash, Diatomite and Raw Illite: Formation of Nitride Powders with Different Morphology and Photoluminescence Properties

Fabrication of one-dimensional rod-like α-SiAlON powders in large scales by combustion synthesis

Fabrication of yttrium-stabilized α -SiAlON powders with rod-like crystals by combustion synthesis

Rapid synthesis of AlON powders by nitriding combustion synthesis precursor

Effect of Impurities MgO, CaO, Al2O3, AlN and Al on Α/β Ratio in Combustion Synthesis of Α-Si3n4

Combustion synthesis of alpha SiAlON powders with low oxygen contents by using fluorides as reactants

Combustion Synthesis of α-SiAlON Powders with Low Oxygen Contents by Using Fluorides as Reactants

One-step Carbothermal Reduction and Nitridation (CRN) for Fast Fabrication of Fine and Single Phase AlON Powder by Using Hydrothermal Synthesized Α-Al2o3/c Mixture