Abstract:To meet the practical application, a kind of commercially available Si3N4 powder by direct Si nitridation was used to fabricate dense Si3N4/SiC nanocomposite by pressureless sintering method. The price of this kind of powder is much lower than that of powder by imide decomposition. 5-30 vol% of SiC powder (average particle size: 80 nm) were added in the composite to investigate the effect of SiC particle. Totally 15 wt% of MgAl2O4 and ZrO2 (50 wt% each) were used as sihtering additives. With increasing SiC content, the densities of the composites decreased. α-β Si3N4 phase transformation was enhanced at low temperatures, but prohibited at high temperatures for large SiC content. The sample with larger SiC content gave a relatively smaller Si3N4 grain size because SiC particles limit the Si3N4 grain growth by pinning and prohibiting the grain boundary movement. An improvement of Young's modulus, flexural strength and hardness by the SiC addition was found. Further increase in SiC content resulted in a decrease of these properties because of the decreasing density for the samples sintered at low temperatures. With an intermediate sintering temperature, the samples with 20 vol% SiC reached to high flexural strength as 1050 MPa as a result of good density and relatively fine grain size structure. The decreased fracture toughness with increasing the SiC content was observed by the refinement of Si3N4 grain. However, it was improved with the increasing sintering temperature. The result of this study provided an economic way to fabricate the Si3N4/SiC nanocomposite with a strength higher than 1 GPa and appropriate fracture toughness.

Effect of SiCP Content on β-SiAlON/SiC Nanocomposite Ceramic

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Effects of residual stress and intragranular particles on mechanical properties of hot-pressed Al2O3/SiC ceramic composites

Effect of Si/C Ratio and Their Content on the Microstructure and Properties of Si–B–C–N Ceramics Prepared by Spark Plasma Sintering Techniques

Effects of Sintering Additive and Β-Si3n4 Phase Contents on the Properties of Porous Si3N4 Ceramics

Effects of in situ Mg-Sialon and β-Sialon on the microstructure and properties of MgAl2O4-SiC composites

Effects of SiC contents on the microstructure and mechanical properties of Al4SiC4–SiC ceramic composites

Effect of SiC Addition on Mechanical Properties of Hot-Pressed Al2O3-GdAlO3 Ceramics with Eutectic Composition

Study of SiC/Al nanocomposites under high pressure

Effect of Nano SiC on Microstructure and Mechanical Properties of BN-ZrO2-SiC Multiphase Ceramics

Effect Of Aln Content On The Pressureless Sintering Behaviors Of Sic-Aln Multiphase Ceramics

Densification and Mechanical Properties of Si3N4/SiC Nanocomposite Using Si-Nitrided Si3N4 Powder

Fabrication and Mechanical Properties of Si3N4/SiC Nanocompoisites under Pressureless Sintering.

Effects Of Carbon Addition On Densification And Mechanical Properties Of Porous Si3n4 Ceramics

Effect of solid contents on the mechanical properties of SiC-10 wt.%AlN ceramic composites prepared by gelcasting

The Effects of SiCp Addition on the Z-Value and Mechanical Properties of Β-Sialon–sicp Refractories

Study on the mechanical properties and microstructure of Al2O3/nano-SiC multiphase ceramics

Influence of SiC particle size on microstructure and mechanical properties of Al2O3-SiC nanocomposites

Silicon carbide particle size effects in Al2O3-SiC nanocomposites

Effect of Al 2 O 3 addition on properties of non-sintered SiC–Si 3 N 4 composite refractory materials

Particle agglomeration and mechanical properties of SiCp/Al-Si composites