Abstract:This chapter focuses on the generation, development, inheritance and control of the defects in colloidal forming process, by which the complex near-net shape ceramic products with a homogeneous microstructure and high reliability were consequentially achieved.The rheological performance of the ceramics suspension was very important to the colloid forming processes. In our studies, the rheological behaviors of aqueous alumina suspensions were investigated, and the various ways of modifying the rheological behaviors of the suspensions were discussed. A critical solid loading between the shear thinning and shear thickening behavior was found in an aqueous alumina suspension. Moreover, the gelation of the suspension with high solid loading of alumina got delayed and the strength of green body decreased, which implies that the fast polymerization of monomers in high solid loading alumina suspension was inhibited, and the flexibility of the gel-casting was improved. We found that there was an optimal solid loading for the ZTA suspension to obtain the highest bending strength and the highest Weibull modulus for the sintered bodies.Micro mechanisms of agglomerations' generation in ceramic suspensions used in colloidal forming processing were investigated. On the basis of potential energy between particles in liquid, a microscopic model of agglomerations in ceramic suspensions was presented. Two types of agglomerations, tight agglomeration and loose agglomeration, were observed by using an environmental scanning microscope as a quasi-direct method. It is observed that their generation is caused by the deviation of solid phase content in slurry from the stable solid loading.The influences of the idle time on the microstructures and mechanical properties of green bodies were also described using direct coagulation casting. The vertically laminates cracks were observed in coagulated green bodies after casting using increasing ionic strength. The cracks were attributed to the shrinkage of the particle network (syneresis) during coagulation.The study indicated that the solid loading in the suspension depended on high valence counter-ions and ion conductivity constants. Further research revealed that the inner stress in the green bodies of ceramics originated from the non-uniform shrinkage during the solidification of the precursor suspension and the drying of the green bodies. The gradients of temperature, initiator concentration and moisture are the important original factors causing the inner stress.It is found that a proper amount of a water-soluble polymer, such as hydroxyethyl acrylate (HEA), polyethylene glycol (PEG) and poly (vinylpyrrolidone) (PVP) added into the concentrated suspension can adjust polymer network structure and thus reduce the inner stresses and cracking in the ceramic green body. The debindering time of large ceramic parts can be significantly shortened by reducing the harmful inner stresses in the green body.

Preparation and Characterization of Body Granules for Direct Manufacturing of Longquan Celadon

Inorganic Fiber Reinforced Geyao Longquan Celadon Body

Design and Application of Natural Gas Shuttle Kiln for Firing Longquan Celadon

RESEARCH ON PREPARATION OF SUPERFINE ALUMINA NANONPOWDER AND REINFORCED CELADON CERAMIC BODY

Surface Treatment and Modification of Al2O3 Powders

DISPERSIBILITY MECHANISM AND SPRAY DRYING OF SiC AQUEOUS SLURRY

Influence of Alumina Slurry on Morphology of Microspheres by Spray Drying

Study on the molding process and quality standard of Qizhi Yifei granules

Cylindrical granules in the development of mesalazine solid formulations (II): the contribution of high aspect ratio to favorable tabletability

Characterization of Spray Granulated Nd:Yag Particles for Transparent Ceramics

Preparation and Characterization of Monodispersed and Spherical YAG Powder for Transparent Ceramic by Spray Drying

Generation, Development, Inheritance, and Control of the Defects During the Transformation from Suspension to Green Body

The preparation, characterization, and application of porous core–shell composite particles produced with laboratory-scale spray dryer

Study on Preparation Technology and Physical Fingerprint of Chuilian Jianpi Granules Based on QbD

Multiple-analytical study on the technology of Zhaili celadon from the late sixth to the seventh centuries and its initiation

Optimization of preparation technique for the Qiyuejiangzhi tablets

Effect of dispersant and binder on the morphology of zirconia granules during spray drying

Novel dry-suspension granulation process for preparing pressed powders of ceramic tiles

Systematic optimization of spray drying for YAG transparent ceramics

Application of Near-Infrared Spectrometry to Evaluate the Mechanism of Wet Granulation Using a High-Speed Mixer with Porous Calcium Silicate and Sugar Alcohols.

Storage Stability of Ceramic Slurries for Gelcasting