Abstract:This paper presents an experimental study on controlled ASSCI (Assisted Spark Stratified Compression Ignition) for engine knock suppression in a GDI engine with high compression ratio. The direct injection is used for forming desired stoichiometric stratified mixture at WOT condition without turbo-charging. The engine is filled with 20% cooled external EGR and the ignition timing is maintained at MBT point. The combustion characteristics of the desired stoichiometric stratified mixture show two-stage heat release, where the first stage is caused by spark ignition and the second stage is due to moderate auto-ignition. Compared with engine knock, the second stage heat release of controlled ASSCI shows smooth pressure curve without pressure oscillation. This is due to the low energy density mixture around the cylinder wall caused by cooled external EGR. The stratified mixture could suppress knock. Fuel economy and combustion characteristics of the baseline and the controlled ASSCI combustion were compared. The baseline GDI engine reaches a maximum of 8.9 bar BMEP with BSFC of 291 g/(kWh), the controlled ASSCI combustion achieves a maximum of 8.3 bar BMEP with BSFC of 256 g/(kWh), improving the fuel economy over 12% while maintaining approximately the same power. CA50 (the crank angle of 50% heat release) of the controlled ASSCI is detected at 8.4 degrees CA ATDC, which is degrees 17.4 CA advanced than that of the baseline while the combustion duration of the controlled ASSCI is 52.8 degrees CA, 16.6 degrees CA longer than that of the baseline caused by diluted mixture and two-stage heat release. The COV of the controlled ASSCI is 1.4%, 2.1% lower than that of the baseline. The peak pressure (P-max and the maximum pressure rise rate (PRRmax) of the controlled ASSCI are 59.7 bar and 2.2 bar/degrees CA, 22.9 bar and 1.5 bar/degrees CA higher than that of the baseline respectively. The crank angle of P-max and PRRmax of the controlled ASSCI are 11 degrees CA ATDC and -1 degrees CA ATDC, 15.4 degrees CA and 17.2 degrees CA earlier than that of the baseline. The results show that controlled ASSCI with two-stage heat releases is a potential combustion strategy to suppress engine knock while achieving high efficiency of the high compression ratio gasoline engine.

Design of Knock Control System for GDI Turbocharged Engine Based on Model

Automatic Knock Control System

Vehicle engine knock analysis and control

A Knock Onset Predicting Model for Low Pressure Cooled EGR Boosted Gasoline Engines

Suppression of Super-Knock in TC-GDI Engine Using Two-Stage Injection in Intake Stroke (TSII)

Beta-Distribution-Based Knock Probability Estimation, Control Scheme, and Experimental Validation for SI Engines

A Predictive Model for Knock Onset in Spark-Ignition Engines with Cooled EGR

Progressive strategies to avoid and exploit knock limit for optimal performance and stoichiometric operation of a DI hydrogen engine with high CR at WOT conditions

Engine Control Design Using Globally Linearizing Control and Sliding Mode

Simulation Research on the Effect of Cooled EGR, Supercharging and Compression Ratio on Downsized SI Engine Knock

Experiment and Simulation Study on Performance and Knocking of Turbocharged DISI Engine

Experiment Study and Numerical Analysis of Suppressing Knock with Scavenging for Turbocharged GDI Engine

Controlled Assci With Moderate Auto-Ignition For Engine Knock Suppression In A Gdi Engine With High Compression Ratio

An experimental study of knock analysis of HCNG fueled SI engine by different methods and prediction of knock intensity by particle swarm optimization-support vector machine

A Design of Universal and Programmable Knock Detection Module

Optimization of a Spark Ignition Engine Knock and Performance Using the Epsilon-Constrained Differential Evolution Algorithm and Multi-Objective Differential Evolution Algorithm

Knock Prediction Improvement with Application to the Analysis of Knock Mitigation with Targeted Water Injection in SI Engines

Research and Development of GDI Engine Control System Based on Torque Coordination

Knock Intensity Distribution and a Stochastic Control Framework for Knock Control

Knock Recognition of Knock Sensor Signal Based on Wavelet Transform and Variational Mode Decomposition Algorithm

Knock Control Based on Discrete Wavelet Transform and FPGA