Abstract:The MAX phase has attracted much attention due to its unique properties combined with the merits of both metal and ceramic, including the low density, high electrical conductivity and good oxidation resistance, which makes it significant for possible applications in various high temperature or other environments. There is a lot of research work on Ti2AlX (X=C, N). However little research about thermodynamic properties at high pressure is carried out. So we study the structural, mechanical and thermodynamic properties of Ti2AlC and Ti2AlN at various pressures and temperatures. The first-principles calculations based on electronic density-functional theory framework are used to investigate the properties at various pressures. The cut-off energy is 350 eV. Converged results are achieved with 10102 special K-point meshes. The self-consistent convergence of total energy is set to be 5.010-6 eV/atom. According to the calculated structural parameters at various pressures, we can find that the ratios V/V0 (V0 denotes the system volume at 0 GPa) of Ti2AlX are reduced by 20.59% and 18.93%, respectively, so the compressibility of the system is strong. As the internal pressure increases, the curves of V/V0 become gentle. Then we calculate elastic constants at pressures ranging from 0 to 50 GPa in steps of 10 GPa. It is obvious that the Ti2AlX is mechanically stable because all of the elastic constants satisfy the Born stability criteria. The bulk modulus, shear modulus and Young's modulus linearly increase with internal pressure increasing, implying that the pressure can improve the resistance to volume deformation. The ductility and brittleness can be judged according to Pugh's criterion (ratio of bulk modulus to shear modulus B/G), and the brittle nature turns into ductile nature in a pressure range of 40-50 GPa for the Ti2AlX since the value of B/G exceeds 1.75. Finally, we study the thermodynamic properties at various pressures and temperatures based on the quasi-harmonic Debye approximation theory, including the bulk modulus, heat capacity and thermal expansion coefficient. The bulk modulus decreases with temperature increasing but increases with pressure increasing. The heat capacity at constant volume Cv and the heat capacity at constant pressure Cp have the same variation tendency, while Cv obeys the Dulong-Petit limit. It is easy to see that temperature and pressure have opposite influences on heat capacity and the effect of temperature is more significant than that of pressure. The effects of temperature and pressure on linear expansion coefficient mainly occur at low temperature and the effect of pressure is not so considerable when the pressure exceeds 30 GPa. Above all, the effects of temperature and pressure on thermodynamic properties are inverse.

Influence of heat treatment on microstructure and nanohardness of TiAl alloy solidified under high pressure

Evolution of the microstructure and nanohardness of Ti-48at.%Al alloy solidified under high pressure

High Pressure Solidification Process and Effect on Nanohardness of Ti–48 At-%Al Alloy

Effect of High Pressure on the Lamellar Spacing and Mechanical Properties of Ti-48al Alloy

Properties of Commercial Pure Titanium under Self-Heating and High-Pressure Heating Treatment

Effect of High Temperature-High Pressure Treatment on Microstructure and Mechanical Properties of Cu-Cr Alloy

Effect of Heat Treatment on the Microstructure and Mechanical Properties of TiAl Alloys

Effect of composition, annealing temperature, and high pressure torsion on structure and hardness of Ti–V and Ti–V–Al alloys

Microstructures of TiAl 3 intermetallic compound solidified under ultra high pressure

Effects of heat treatment on hydriding/dehydriding characteristics of Ti18Cr24V55Zr3 alloy

Structural, Mechanical, and Thermodynamic Properties of Ti2AlX (X = C, N) at High Pressure

Influence of Heat Treatment on the Microstructure and Hydrogen Storage Properties of Ti10V77Cr6Fe6Zr Alloy

Microstructural Evolution and Mechanical Strengthening Mechanism of the High Pressure Heat Treatment (HPHT) on Al-Mg Alloy

Effect of Heat Treatment on Microstructures Evolution of Rapidly Solidified Ti-48Al-4Cr Alloy

Microstructure Evolution and Mechanical Properties of High Nb-TiAl Intermetallic Compounds during Heat Treatment

Effects of 3 GPa High Pressure Treatment on the Β1→ Α + Β2phase Transition Dynamics of TC4 Titanium Alloy

Effect of high pressure treatment on Ni50Al30Fe20 intermetallic alloy

Effect of Heat Treatment on Microstructures and Mechanical Properties of a Novel Β-Solidifying TiAl Alloy

Influence Of Heat Treatment On The Microstructure And Properties Of Ti2alc By Shs/Phip

Effect of pressure on microstructure and properties of Ti–Al coating on titanium alloy surface

The Effect of Heat Treatment on the Microstructure and Mechanical Properties of Powder Metallurgy Ti-48Al Alloy