Abstract:The MAX phase has attracted much attention due to its unique properties combined with the merits of both metal and ceramic, including the low density, high electrical conductivity and good oxidation resistance, which makes it significant for possible applications in various high temperature or other environments. There is a lot of research work on Ti2AlX (X=C, N). However little research about thermodynamic properties at high pressure is carried out. So we study the structural, mechanical and thermodynamic properties of Ti2AlC and Ti2AlN at various pressures and temperatures. The first-principles calculations based on electronic density-functional theory framework are used to investigate the properties at various pressures. The cut-off energy is 350 eV. Converged results are achieved with 10102 special K-point meshes. The self-consistent convergence of total energy is set to be 5.010-6 eV/atom. According to the calculated structural parameters at various pressures, we can find that the ratios V/V0 (V0 denotes the system volume at 0 GPa) of Ti2AlX are reduced by 20.59% and 18.93%, respectively, so the compressibility of the system is strong. As the internal pressure increases, the curves of V/V0 become gentle. Then we calculate elastic constants at pressures ranging from 0 to 50 GPa in steps of 10 GPa. It is obvious that the Ti2AlX is mechanically stable because all of the elastic constants satisfy the Born stability criteria. The bulk modulus, shear modulus and Young's modulus linearly increase with internal pressure increasing, implying that the pressure can improve the resistance to volume deformation. The ductility and brittleness can be judged according to Pugh's criterion (ratio of bulk modulus to shear modulus B/G), and the brittle nature turns into ductile nature in a pressure range of 40-50 GPa for the Ti2AlX since the value of B/G exceeds 1.75. Finally, we study the thermodynamic properties at various pressures and temperatures based on the quasi-harmonic Debye approximation theory, including the bulk modulus, heat capacity and thermal expansion coefficient. The bulk modulus decreases with temperature increasing but increases with pressure increasing. The heat capacity at constant volume Cv and the heat capacity at constant pressure Cp have the same variation tendency, while Cv obeys the Dulong-Petit limit. It is easy to see that temperature and pressure have opposite influences on heat capacity and the effect of temperature is more significant than that of pressure. The effects of temperature and pressure on linear expansion coefficient mainly occur at low temperature and the effect of pressure is not so considerable when the pressure exceeds 30 GPa. Above all, the effects of temperature and pressure on thermodynamic properties are inverse.

Effects of 3 GPa High Pressure Treatment on the Β1→ Α + Β2phase Transition Dynamics of TC4 Titanium Alloy

The effect of heat treatment system on mechanical properties of titanium alloy BTi-6554

Theoretical Investigation of the High Pressure Structure, Lattice Dynamics, Phase Transition, and Thermal Equation of State of Titanium Metal

Effect of 4 Gpa Pressure Treatment on the Solid State Transformation Kinetics of T8 Steel in Heating Process

Effect of High Temperature-High Pressure Treatment on Microstructure and Mechanical Properties of Cu-Cr Alloy

Properties of Commercial Pure Titanium under Self-Heating and High-Pressure Heating Treatment

Structural, Mechanical, and Thermodynamic Properties of Ti2AlX (X = C, N) at High Pressure

Effect of composition, annealing temperature, and high pressure torsion on structure and hardness of Ti–V and Ti–V–Al alloys

Hot Deformation Behavior of a Novel Near-β Titanium Alloy Ti-5.5Mo-6V-7Cr-4Al-2Sn-1Fe in (α+β) Phase Region

Pressure Effects on Solid State Phase Transformation of Aluminium Bronze in Cooling Process

Pressure-Induced Reversible Hcp to Fcc Phase Transition of Ti: A First-Principles Study

Influence of High Pressure Treatment on Microstructure Evolution of Cu–Zn Alloy

Effects of heat treatment process on microstructure and hardness of TC4 titanium alloy

Effect of multi-pass cooling compression and subsequent heat treatment on microstructural and mechanical evolution of TC4 alloys

Experimental constraints on the phase diagram of titanium metal

The Determining Influence of the Phase Composition on the Mechanical Properties of Titanium-Iron Alloys after High-Pressure Torsion

Effect of High-Pressure Torsion on Phase Formation and Mechanical Properties of a High-Entropy TiZrHfMoCrCo Alloy

Thermal Equations of State for Titanium Obtained by High Pressure—temperature Diffraction Studies

The Influence of Deep Cryogenic Treatment (DCT) on the Microstructure Evolution and Mechanical Properties of TC4 Titanium Alloy

Effect of Temperature and Rate Treatment Parameters on the Structural Phase State and Properties of Ti2AlNb Titanium Aluminide-Based Alloy

Latent Heat of TB18 Titanium Alloy during to a Phase Transition by DSC and First-Principles Methods