Abstract:The MAX phase has attracted much attention due to its unique properties combined with the merits of both metal and ceramic, including the low density, high electrical conductivity and good oxidation resistance, which makes it significant for possible applications in various high temperature or other environments. There is a lot of research work on Ti2AlX (X=C, N). However little research about thermodynamic properties at high pressure is carried out. So we study the structural, mechanical and thermodynamic properties of Ti2AlC and Ti2AlN at various pressures and temperatures. The first-principles calculations based on electronic density-functional theory framework are used to investigate the properties at various pressures. The cut-off energy is 350 eV. Converged results are achieved with 10102 special K-point meshes. The self-consistent convergence of total energy is set to be 5.010-6 eV/atom. According to the calculated structural parameters at various pressures, we can find that the ratios V/V0 (V0 denotes the system volume at 0 GPa) of Ti2AlX are reduced by 20.59% and 18.93%, respectively, so the compressibility of the system is strong. As the internal pressure increases, the curves of V/V0 become gentle. Then we calculate elastic constants at pressures ranging from 0 to 50 GPa in steps of 10 GPa. It is obvious that the Ti2AlX is mechanically stable because all of the elastic constants satisfy the Born stability criteria. The bulk modulus, shear modulus and Young's modulus linearly increase with internal pressure increasing, implying that the pressure can improve the resistance to volume deformation. The ductility and brittleness can be judged according to Pugh's criterion (ratio of bulk modulus to shear modulus B/G), and the brittle nature turns into ductile nature in a pressure range of 40-50 GPa for the Ti2AlX since the value of B/G exceeds 1.75. Finally, we study the thermodynamic properties at various pressures and temperatures based on the quasi-harmonic Debye approximation theory, including the bulk modulus, heat capacity and thermal expansion coefficient. The bulk modulus decreases with temperature increasing but increases with pressure increasing. The heat capacity at constant volume Cv and the heat capacity at constant pressure Cp have the same variation tendency, while Cv obeys the Dulong-Petit limit. It is easy to see that temperature and pressure have opposite influences on heat capacity and the effect of temperature is more significant than that of pressure. The effects of temperature and pressure on linear expansion coefficient mainly occur at low temperature and the effect of pressure is not so considerable when the pressure exceeds 30 GPa. Above all, the effects of temperature and pressure on thermodynamic properties are inverse.

Experimental constraints on the phase diagram of titanium metal

Theoretical Investigation of the High Pressure Structure, Lattice Dynamics, Phase Transition, and Thermal Equation of State of Titanium Metal

Thermal Equations of State for Titanium Obtained by High Pressure—temperature Diffraction Studies

Pressure-Induced Reversible Hcp to Fcc Phase Transition of Ti: A First-Principles Study

ChemInform Abstract: High Pressure in Situ Differential Thermal Analysis of Na0.5Bi0.5TiO3 Phase Transitions Up to 5 GPa.

Pressure-induced alpha-to-omega transition in titanium metal: A systematic study of the effects of uniaxial stress

Experimental Constraints on the Phase Diagram of Elemental Zirconium

Amorphouslike Diffraction Pattern in Solid Metallic Titanium.

Structural, Mechanical, and Thermodynamic Properties of Ti2AlX (X = C, N) at High Pressure

Pressure-induced phase transition and elastic properties of TiO<sub>2</sub>polymorphs

Density functional theory study of the α --> ω martensitic transformation in titanium induced by hydrostatic pressure

Pressure‐induced phase transition and elastic properties of TiO2 polymorphs

Elasticity behavior, phonon spectra, and the pressure-temperature phase diagram of HfTi alloy: A density-functional theory study

Phase transition, mechanical and electronic properties of Ti3B4 under high pressure

Thermodynamic properties of titanium from ab-initio calculations

The molybdenum-titanium phase diagram evaluated from ab-initio calculations

Constitutive Model and Microstructure Evolution of a Novel TG6 High-Temperature Titanium Alloy during Hot Deformation

Pressure and Temperature-Dependent Optical Properties of TiTa2O7

Phase transitions in titanium with an analytic bond-order potential

Effects of 3 GPa High Pressure Treatment on the Β1→ Α + Β2phase Transition Dynamics of TC4 Titanium Alloy

In Situ Phase Transition Study of Nano- and Coarse-Grained Tio(2) under High Pressure/Temperature Conditions