Abstract:The MAX phase has attracted much attention due to its unique properties combined with the merits of both metal and ceramic, including the low density, high electrical conductivity and good oxidation resistance, which makes it significant for possible applications in various high temperature or other environments. There is a lot of research work on Ti2AlX (X=C, N). However little research about thermodynamic properties at high pressure is carried out. So we study the structural, mechanical and thermodynamic properties of Ti2AlC and Ti2AlN at various pressures and temperatures. The first-principles calculations based on electronic density-functional theory framework are used to investigate the properties at various pressures. The cut-off energy is 350 eV. Converged results are achieved with 10102 special K-point meshes. The self-consistent convergence of total energy is set to be 5.010-6 eV/atom. According to the calculated structural parameters at various pressures, we can find that the ratios V/V0 (V0 denotes the system volume at 0 GPa) of Ti2AlX are reduced by 20.59% and 18.93%, respectively, so the compressibility of the system is strong. As the internal pressure increases, the curves of V/V0 become gentle. Then we calculate elastic constants at pressures ranging from 0 to 50 GPa in steps of 10 GPa. It is obvious that the Ti2AlX is mechanically stable because all of the elastic constants satisfy the Born stability criteria. The bulk modulus, shear modulus and Young's modulus linearly increase with internal pressure increasing, implying that the pressure can improve the resistance to volume deformation. The ductility and brittleness can be judged according to Pugh's criterion (ratio of bulk modulus to shear modulus B/G), and the brittle nature turns into ductile nature in a pressure range of 40-50 GPa for the Ti2AlX since the value of B/G exceeds 1.75. Finally, we study the thermodynamic properties at various pressures and temperatures based on the quasi-harmonic Debye approximation theory, including the bulk modulus, heat capacity and thermal expansion coefficient. The bulk modulus decreases with temperature increasing but increases with pressure increasing. The heat capacity at constant volume Cv and the heat capacity at constant pressure Cp have the same variation tendency, while Cv obeys the Dulong-Petit limit. It is easy to see that temperature and pressure have opposite influences on heat capacity and the effect of temperature is more significant than that of pressure. The effects of temperature and pressure on linear expansion coefficient mainly occur at low temperature and the effect of pressure is not so considerable when the pressure exceeds 30 GPa. Above all, the effects of temperature and pressure on thermodynamic properties are inverse.

Microstructures of TiAl 3 intermetallic compound solidified under ultra high pressure

Size Dependent Phase Transformation in Atomized TiAl Powders

Evolution of the microstructure and nanohardness of Ti-48at.%Al alloy solidified under high pressure

Theoretical Investigation of the High Pressure Structure, Lattice Dynamics, Phase Transition, and Thermal Equation of State of Titanium Metal

Microstructure evolution of Al–Mg alloy during solidification under high pressure

Evolution of Microstructures and Phases of Al–Mg Alloy under 4 GPa High Pressure

Structural, Mechanical, and Thermodynamic Properties of Ti2AlX (X = C, N) at High Pressure

The Formation of Bulk Β-Al3ni Phase in Eutectic Al-5.69wt%Ni Alloy Solidified under High Pressure

High Pressure Solidification Microstructure and Stability of Al-9.6%Mg Alloy

Microstructure Evolution and Precipitation of SiC Particle Reinforced Al–20Si Composite Solidified under High Pressures

GPa level pressure-induced phase transitions and enhanced corrosion resistance of AlCrMoSiTi high-entropy alloys

Effect of Pressure on the Structure of Ti75Al25 Alloy During Rapid-Quenching Process

Microstructure evolution and precipitation of Al–12Mg alloy solidified under high pressure

Microstructural evolution and precipitation behavior of Al-7Si-3Cu alloy prepared under 5 GPa

Effects of High Pressure and Superheat Temperature on Microstructure Evolution of Al-20Si Alloy

Microstructural Evolution and Mechanical Properties of Al–Si–Cu–(Ge)–(Mg) Alloy Solidified under High Pressure

Orderly Nucleation and Competitive Growth Behaviors of Ti-Al Intermetallic Compounds in Ti/TiAl3 Diffusion Couple under High Temperature

Effect of High Pressure and Temperature on the Evolution of Si Phase and Eutectic Spacing in Al-20Si Alloys

Phase transition, mechanical and electronic properties of Ti3B4 under high pressure

High Pressure Solidification Process and Effect on Nanohardness of Ti–48 At-%Al Alloy

Effect of High Pressure on the Lamellar Spacing and Mechanical Properties of Ti-48al Alloy