Abstract:The MAX phase has attracted much attention due to its unique properties combined with the merits of both metal and ceramic, including the low density, high electrical conductivity and good oxidation resistance, which makes it significant for possible applications in various high temperature or other environments. There is a lot of research work on Ti2AlX (X=C, N). However little research about thermodynamic properties at high pressure is carried out. So we study the structural, mechanical and thermodynamic properties of Ti2AlC and Ti2AlN at various pressures and temperatures. The first-principles calculations based on electronic density-functional theory framework are used to investigate the properties at various pressures. The cut-off energy is 350 eV. Converged results are achieved with 10102 special K-point meshes. The self-consistent convergence of total energy is set to be 5.010-6 eV/atom. According to the calculated structural parameters at various pressures, we can find that the ratios V/V0 (V0 denotes the system volume at 0 GPa) of Ti2AlX are reduced by 20.59% and 18.93%, respectively, so the compressibility of the system is strong. As the internal pressure increases, the curves of V/V0 become gentle. Then we calculate elastic constants at pressures ranging from 0 to 50 GPa in steps of 10 GPa. It is obvious that the Ti2AlX is mechanically stable because all of the elastic constants satisfy the Born stability criteria. The bulk modulus, shear modulus and Young's modulus linearly increase with internal pressure increasing, implying that the pressure can improve the resistance to volume deformation. The ductility and brittleness can be judged according to Pugh's criterion (ratio of bulk modulus to shear modulus B/G), and the brittle nature turns into ductile nature in a pressure range of 40-50 GPa for the Ti2AlX since the value of B/G exceeds 1.75. Finally, we study the thermodynamic properties at various pressures and temperatures based on the quasi-harmonic Debye approximation theory, including the bulk modulus, heat capacity and thermal expansion coefficient. The bulk modulus decreases with temperature increasing but increases with pressure increasing. The heat capacity at constant volume Cv and the heat capacity at constant pressure Cp have the same variation tendency, while Cv obeys the Dulong-Petit limit. It is easy to see that temperature and pressure have opposite influences on heat capacity and the effect of temperature is more significant than that of pressure. The effects of temperature and pressure on linear expansion coefficient mainly occur at low temperature and the effect of pressure is not so considerable when the pressure exceeds 30 GPa. Above all, the effects of temperature and pressure on thermodynamic properties are inverse.

Effect of Pressure on the Structure of Ti75Al25 Alloy During Rapid-Quenching Process

Theoretical Investigation of the High Pressure Structure, Lattice Dynamics, Phase Transition, and Thermal Equation of State of Titanium Metal

Effect of High Pressure on Microstructure of Crystallizing Amorphous Nd9Fe85B6 Alloy

Molecular dynamics study of structural evolution of aluminum during rapid quenching under different pressures

Structural, Mechanical, and Thermodynamic Properties of Ti2AlX (X = C, N) at High Pressure

Effects of pressure on microstructure evolution of liquid Fe-S-Bi alloy during rapid solidification: A molecular dynamics study

Pressure Effects on Al89La6Ni5 Amorphous Alloy Crystallization

First-principles Study of Ni-Al Intermetallic Compounds under Various Temperature and Pressure

Effect of High Temperature-High Pressure Treatment on Microstructure and Mechanical Properties of Cu-Cr Alloy

Physical properties and Debye temperature of Al7Cu2Fe alloy under various pressures analyzed by first-principles

Theoretical Study on the Structural, Elastic, Electronic and Thermodynamic Properties of Long-Period Superstructures h- and r-Al2Ti under High Pressure

Effect of Rapid Quenching on Phase Structure and Hydrogen Storage Performance of Ti-V-Based Bcc Phase Alloys

Anisotropy in Elasticity and Physical Properties of Ti2B under High Pressure

Pressure-Induced Reversible Hcp to Fcc Phase Transition of Ti: A First-Principles Study

High-pressure X-Ray Diffraction of Icosahedral Zr–Al–Ni–Cu–Ag Quasicrystals

Pressure Effect on Elastic Constants and Related Properties of Ti3Al Intermetallic Compound: A First-Principles Study

Effect of high pressure treatment on Ni50Al30Fe20 intermetallic alloy

GPa level pressure-induced phase transitions and enhanced corrosion resistance of AlCrMoSiTi high-entropy alloys

Effects of Pressure on Homogeneous Nucleation and Growth during Isothermal Solidification in Pure Al: A Molecular Dynamics Simulation Study

Phase Transformations of Al-bearing High-Entropy Alloys AlxCoCrFeNi (x=0, 0.1, 0.3, 0.75, 1.5) at High Pressure

Simulation Study of Effects of Ti Content on Microstructure Evolution and Elastic Constants of Immiscible Mg-Ti Alloys During Rapid Quenching Process